Ucertify ccent 100 105 Questions are updated and all ccent 100 105 answers are verified by experts. Once you have completely prepared with our 105 100 exam prep kits you will be ready for the real ccent 100 105 exam without a problem. We have Improve Cisco icnd1 100 105 pdf dumps study guide. PASSED 100 105 icnd1 pdf First attempt! Here What I Did.
2026 New 100-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/100-105/
P.S. Validated 100-105 practice are available on Google Drive, GET MORE: https://drive.google.com/open?id=1p6goOol79JPy5WQ9QjPXU5ZCXFzabnVd
New Cisco 100-105 Exam Dumps Collection (Question 7 - Question 16)
Q1. Refer to the exhibit.
The network administrator is testing connectivity from the branch router to the newly installed application server. What is the most likely reason for the first ping having a success rate of only 60 percent?
A. The network is likely to be congested, with the result that packets are being intermittently dropped.
B. The branch router had to resolve the application server MAC address.
C. There is a short delay while NAT translates the server IP address.
D. A routing table lookup delayed forwarding on the first two ping packets.
E. The branch router LAN interface should be upgraded to FastEthernet.
Answer: B
Explanation:
Initially the MAC address had to be resolved, but once it is resolved and is in the ARP table of the router, pings go through immediately.
Q2. On a live network, which commands will verify the operational status of router interfaces? (Choose two.)
A. Router# show interfaces
B. Router# show ip protocols
C. Router# debug interface
D. Router# show ip interface brief
E. Router# show start
Answer: A,D
Explanation:
Only two commands u201cshow interfacesu201d and u201cshow ip interface briefu201d reveal the status of router interfaces (up/up, for example).
Q3. Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the issue?
A. R1 ethernetO/1 is shutdown. Configure no shutdown command.
B. R1 ethernetO/1 configured with a non-default OSPF hello interval of 25: configure no ip ospf hello-interval 25
C. R2 ethernetO/1 and R3 ethernetO/O are configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
D. Enable OSPF for R1 ethernetO/1; configure ip ospf 1 area 0 command under ethernetO/1
Answer: B
Explanation:
Looking at the configuration of R1, we see that R1 is configured with a hello interval of 25 on interface Ethernet 0/1 while R2 is left with the default of 10 (not configured).
Q4. Which statements are true regarding ICMP packets? (Choose two.)
A. They acknowledge receipt of TCP segments.
B. They guarantee datagram delivery.
C. TRACERT uses ICMP packets.
D. They are encapsulated within IP datagrams.
E. They are encapsulated within UDP datagrams.
Answer: C,D
Explanation:
Ping may be used to find out whether the local machines are connected to the network or whether a remote site is reachable. This tool is a common network tool for determining the network connectivity, which uses ICMP protocol instead of TCP/IP and UDP/IP. This protocol is usually associated with the network management tools, which provide network information to network administrators, such as ping and traceroute (the later also uses the UDP/IP protocol).
ICMP is quite different from the TCP/IP and UDP/IP protocols. No source and destination ports are included in its packets. Therefore, usual packet-filtering rules for TCP/IP and UDP/IP are not applicable. Fortunately, a special "signature" known as the packetu2021s Message type is included for denoting the purposes of the ICMP packet. Most commonly used message types are namely, 0, 3, 4, 5, 8, 11, and 12 which represent echo reply, destination unreachable, source quench, redirect, echo request, time exceeded, and parameter problem respectively.
In the ping service, after receiving the ICMP "echo request" packet from the source location, the destination
Q5. Refer to the exhibit.
Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?
A. 10.1.1.2
B. 10.154.154.1
C. 172.16.5.1
D. 192.168.5.3
Answer: C
Explanation:
The highest IP address of all loopback interfaces will be chosen -> Loopback 0 will be chosen as the router ID.
Q6. Some routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Answer: B,D
Explanation:
Cisco administration 101: What you need to know about default routes Reference:
http://www.techrepublic.com/article/cisco-administration-101-what-you-need-to-know- about-default-routes/
Q7. Refer to the exhibit.
Mary is sending an instant message to Robert. The message will be broken into a series of packets that will traverse all network devices. What addresses will populate these packets as they are forwarded from Router1 to Router2?
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
Answer: B
Explanation:
The Source and Destination IP address is not going to change. Host 1 IP address will stay as being the source IP and the Host 2 IP address will stay the destination IP address. Those two are not going to change.
For the MAC address it is going to change each time it goes from one hope to another. (Except switches... they don't change anything)
Frame leaving HOST 1 is going to have a source MAC of Host 1 and a destination MAC of Router 1.
Router 1 is going to strip that info off and then will make the source MAC address of Router1's exiting interface, and making Router2's interface as the destination MAC address.
Then the same will happen... Router2 is going to change the source/destination info to the source MAC being the Router2 interface that it is going out, and the destination will be Host2's MAC address.
Topic 2, LAN Switching Technologies
41.Refer to the exhibit.
All devices attached to the network are shown. How many collision domains are present in this network?
A. 2
B. 3
C. 6
D. 9
E. 15
Q8. Refer to the exhibit.
A person is trying to send a file from a host on Network A of the JAX Company to a server on Network Z of the XYZ Company. The file transfer fails. The host on Network A can communicate with other hosts on Network A.
Which command, issued from router RTA, would be the most useful for troubleshooting this problem?
A. show flash:
B. show history
C. show version
D. show interfaces
E. show controllers serial
Answer: D
Explanation:
The most useful thing to check on RTA would be the show interfaces command to see if the interface toward the WAN link is up. The most likely scenario is that the local LAN interface is up, but the other interface toward the XYZ company is down.
Q9. Refer to the exhibit.
If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?
A. 192.168.1.1
B. 172.16.1.1
C. 1.1.1.1
D. 2.2.2.2
Answer: D
Explanation:
If a router-id is not configured manually in the OSPF routing process the router will automatically configure a router-id determined from the highest IP address of a logical interface (loopback interface) or the highest IP address of an active interface. If more than one loopback interfaces are configured, the router will compare the IP addresses of each of the interfaces and choose the highest IP address from the loopbacks.
Q10. What OSPF command, when configured, will include all interfaces into area 0?
A. network 0.0.0.0 255.255.255.255 area 0
B. network 0.0.0.0 0.0.0.0 area 0
C. network 255.255.255.255 0.0.0.0 area 0
D. network all-interfaces area 0
Answer: A
Explanation:
Example 3-1 displays OSPF with a process ID of 1 and places all interfaces configured with an IP address in area 0. The network command network 0.0.0.0 255.255.255.255 area 0
dictates that you do not care (255.255.255.255) what the IP address is, but if an IP address is enabled on any interface, place it in area 0.
Example 3-1 Configuring OSPF in a Single Area
router ospf 1
network 0.0.0.0 255.255.255.255 area 0
Reference: http://www.ciscopress.com/articles/article.asp?p=26919&seqNum=3
P.S. Easily pass 100-105 Exam with Surepassexam Validated Dumps & pdf vce, Try Free: https://www.surepassexam.com/100-105-exam-dumps.html (347 New Questions)