Act now and download your Cisco ccna routing and switching icnd2 200 105 official cert guide test today! Do not waste time for the worthless Cisco ccna 200 105 tutorials. Download Improved Cisco ICND2 Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) exam with real questions and answers and begin to learn Cisco 200 105 icnd2 with a classic professional.
2026 New 200-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-105/
P.S. Realistic 200-105 courses are available on Google Drive, GET MORE: https://drive.google.com/open?id=1zYK40K7kFi-jMIoxBFium4FkX2FixrbS
New Cisco 200-105 Exam Dumps Collection (Question 15 - Question 24)
New Questions 15
What can cause two OSPF neighbors to be stuck in the EXSTART state?
A. There is a low bandwidth connection between neighbors.
B. The neighbors have different MTU settings.
C. The OSPF interfaces are in a passive state.
D. There is only layer one connectivity between neighbors.
Answer: B
Explanation:
Neighbors Stuck in Exstart/Exchange State
The problem occurs most frequently when attempting to run OSPF between a Cisco router and another vendor's router. The problem occurs when the maximum transmission unit (MTU) settings for neighboring router interfaces don't match. If the router with the higher MTU sends a packet larger that the MTU set on the neighboring router, the neighboring router ignores the packet.0 When this problem occurs, the output of the show ip ospf neighbor command displays output similar that shown below:
router-6# show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface 170.170.11.7 1 EXCHANGE/ - 00:00:36 170.170.11.7 Serial2.7
router-6#
router-7# show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface 170.170.11.6 1 EXSTART/ - 00:00:33 170.170.11.6 Serial0.6
Reference: http://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first- ospf/13684-12.html
New Questions 16
Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?
A. The GRE tunnel destination is not configured on the R2 router.
B. The GRE tunnel destination is not configured on the Branch2 router.
C. The static route points to the tunnel0 interface that is misconfigured on the Branch2 router.
D. The static route points to the tunnel0 interface that is misconfigured on the R2 router.
Answer: C
New Questions 17
Which two statements about the OSPF Router ID are true? (Choose two.)
A. It identifies the source of a Type 1 LSA.
B. It should be the same on all routers in an OSPF routing instance.
C. By default, the lowest IP address on the router becomes the OSPF Router ID.
D. The router automatically chooses the IP address of a loopback as the OSPF Router ID.
E. It is created using the MAC Address of the loopback interface.
Answer: A,D
Explanation:
From the output of the u201cshow ip ospf databaseu201d:
New Questions 18
Refer to the exhibit.
A technician has configured the FastEthernet 0/1 interface on Sw11 as an access link in VLAN 1. Based on the output from the show vlan brief command issued on Sw12, what will be the result of making this change on Sw11?
A. Only the hosts in VLAN 1 on the two switches will be able to communicate with each other.
B. The hosts in all VLANs on the two switches will be able to communicate with each other.
C. Only the hosts in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other.
D. Hosts will not be able to communicate between the two switches.
Answer: D
Explanation:
VLANs are local to each switch's database, and VLAN information is not passed between switches without implementing VLAN Trunk Protocol (VTP). Trunks carry traffic from all VLANs to and from the switch by default but, can be configured to carry only specified VLAN traffic. Trunk links are required to pass VLAN information between switches. So Sw11 port should be trunk not access port. Additionally, there are no ports assigned to VLAN 1.
New Questions 19
Which WAN topology provides a direct connection from each site to all other sites on the network?
A. single-homed
B. full mesh
C. point-to-point
D. hub-and-spoke
Answer: B
New Questions 20
What three pieces of information can be used in an extended access list to filter traffic? (Choose three)
A. VLAN number
B. TCP or UDP port numbers
C. source switch port number
D. source IP address and destination IP address
E. protocol
F. source MAC address and destination MAC address
Answer: B,D,E
New Questions 21
Which identification number is valid for an extended ACL?
A. 1
B. 64
C. 99
D. 100
E. 299
F. 1099
Answer: D
New Questions 22
How can you disable DTP on a switch port?
A. Configure the switch port as a trunk.
B. Add an interface on the switch to a channel group.
C. Change the operational mode to static access.
D. Change the administrative mode to access.
Answer: D
New Questions 23
What are two drawbacks of implementing a link-state routing protocol? (Choose two.)
A. the sequencing and acknowledgment of link-state packets
B. the high volume of link-state advertisements in a converged network
C. the requirement for a hierarchical IP addressing scheme for optimal functionality
D. the high demand on router resources to run the link-state routing algorithm
E. the large size of the topology table listing all advertised routes in the converged network
Answer: C,D
New Questions 24
Which option is the benefit of implementing an intelligent DNS for a cloud computing solution?
A. It reduces the need for a backup data center.
B. It can redirect user requests to locations that are using fewer network resources.
C. It enables the ISP to maintain DNS records automatically.
D. It eliminates the need for a GSS.
Answer: B
100% Improved Cisco 200-105 Questions & Answers shared by Thedumpscentre, Get HERE: http://www.thedumpscentre.com/200-105-dumps/ (New 267 Q&As)