Your success in Cisco 200 125 ccna is our sole target and we develop all our ccna 200 125 syllabus braindumps in a way that facilitates the attainment of this target. Not only is our ccna 200 125 torrent study material the best you can find, it is also the most detailed and the most updated. 200 125 ccna book Practice Exams for Cisco CCNA Routing and Switching 200 125 ccna are written to the highest standards of technical accuracy.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. - (Topic 8)
Which two statements about unique local IPv6 addresses are true?
A. They are identical to IPv4 private addresses.
B. They are defined by RFC 1884.
C. They use the prefix FEC0::/10
D. They use the prefix FC00::/7
E. They can be routed on the IPv6 global internet.
Answer: A,D
Q2. - (Topic 6)
Refer to the exhibit.
The following commands are executed on interface fa0/1 of 2950Switch. 2950Switch(config-if)# switchport port-security
2950Switch(config-if)# switchport port-security mac-address sticky 2950Switch(config-if)# switchport port-security maximum 1
The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.)
A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
B. Only host A will be allowed to transmit frames on fa0/1.
C. This frame will be discarded when it is received by 2950Switch.
D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1.
F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1.
Answer: B,D
Explanation:
The configuration shown here is an example of port security, specifically port security using sticky addresses. You can use port security with dynamically learned and static MAC addresses to restrict a port's ingress traffic by limiting the MAC addresses that are allowed to send traffic into the port. When you assign secure MAC addresses to a secure port, the port does not forward ingress traffic that has source addresses outside the group of defined addresses. If you limit the number of secure MAC addresses to one and assign a single secure MAC address, the device attached to that port has the full bandwidth of the port.
Port security with sticky MAC addresses provides many of the same benefits as port security with static MAC addresses, but sticky MAC addresses can be learned dynamically. Port security with sticky MAC addresses retains dynamically learned MAC addresses during a link-down condition.
Q3. - (Topic 8)
Which statement about named ACLs is true?
A. They support standard and extended ACLs.
B. They are used to filter usernames and passwords for Telnet and SSH.
C. They are used to filter Layer 7 traffic.
D. They support standard ACLs only.
E. They are used to rate limit traffic destined to targeted networks.
Answer: A
Explanation:
Named Access Control Lists (ACLs) allows standard and extended ACLs to be given names instead of numbers. Unlike in numbered Access Control Lists (ACLs), we can edit Named Access Control Lists. Another benefit of using named access configuration mode is that you can add new statements to the access list, and insert them wherever you like. With the legacy syntax, you must delete the entire access list before reapplying it using the updated rules.
Q4. - (Topic 8)
On which type of port can switches interconnect for multi-VLAN communication?
A. interface port
B. access port
C. switch port
D. trunk port
Answer: D
Q5. - (Topic 5)
Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)
A. Network A - 172.16.3.48/26
B. Network A - 172.16.3.128/25
C. Network A - 172.16.3.192/26
D. Link A - 172.16.3.0/30
E. Link A - 172.16.3.40/30
F. Link A - 172.16.3.112/30
Answer: B,D
Explanation:
Only a /30 is needed for the point to point link and sine the use of the ip subnet-zero was used, 172.16.3.0/30 is valid. Also, a /25 is required for 120 hosts and again 172.16.3.128/25 is the best, valid option.
Q6. - (Topic 3)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Explanation:
This question is to examine the conditions for OSPF to create neighborhood.
So as to make the two routers become neighbors, each router must be matched with the following items:
1. The area ID and its types;
2. Hello and failure time interval timer;
3. OSPF Password (Optional).
Q7. - (Topic 5)
The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?
A. 8
B. 6
C. 30
D. 32
E. 14
F. 16
Answer: C
Explanation:
Since there is one class C network that means 256 total IP addresses. Since we need 7 LAN blocks and we cannot use the first one (subnet 0) we take 256/8=32 hosts. However, since we need to reserve the network and broadcast addresses for each of these subnets, only 30 total IP addresses are usable.
Q8. - (Topic 4)
What command is used to verify the DLCI destination address in a Frame Relay static configuration?
A. show frame-relay pvc
B. show frame-relay lmi
C. show frame-relay map
D. show frame relay end-to-end
Answer: C
Explanation:
Sample “show frame-relay map” output: R1#sh frame map
Serial0/0 (up): ip 10.4.4.1 dlci 401(0x191,0x6410), dynamic, broadcast,, status defined, active
Serial0/0 (up): ip 10.4.4.3 dlci 403(0x193,0x6430), dynamic, broadcast,, status defined, active
Serial0/0 (up): ip 10.4.4.4 dlci 401(0x191,0x6410), static, CISCO, status defined, active
Q9. - (Topic 8)
Why did Branch1 router lose WAN connectivity with R1 router?
A. The IP address is misconfigured on PPP multilink interface on the Branch1 router.
B. The PPP multilink group is misconfigured on the £ranch1 serial interfaces.
C. The PPP multilink group is misconfigured on the R1 serial interfaces.
D. The Branch1 serial interfaces are placed in a shutdown condition.
Answer: A
Q10. - (Topic 8)
In which three ways is an IPv6 header simpler than an IPv4 header? (Choose three.)
A. Unlike IPv4 headers, IPv6 headers have a fixed length.
B. IPv6 uses an extension header instead of the IPv4 Fragmentation field.
C. IPv6 headers eliminate the IPv4 Checksum field.
D. IPv6 headers use the Fragment Offset field in place of the IPv4 Fragmentation field.
E. IPv6 headers use a smaller Option field size than IPv4 headers.
F. IPv6 headers use a 4-bit TTL field, and IPv4 headers use an 8-bit TTL field.
Answer: A,B,C