Your success in Cisco ccna 200 125 study guide is our sole target and we develop all our ccna routing and switching 200 125 braindumps in a way that facilitates the attainment of this target. Not only is our 200 125 ccna study material the best you can find, it is also the most detailed and the most updated. 200 125 cisco Practice Exams for Cisco CCNA Routing and Switching 200 125 ccna v3 0 are written to the highest standards of technical accuracy.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. - (Topic 8)
Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE
Answer: B
Q2. - (Topic 8)
How does a router handle an incoming packet whose destination network is missing from the routing table?
A. it discards the packet.
B. it broadcasts the packet to each network on the router.
C. it routes the packet to the default route.
D. it broadcasts the packet to each interface on the router.
Answer: A
Q3. - (Topic 8)
Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?
A. The GRE tunnel destination is not configured on the R2 router.
B. The GRE tunnel destination is not configured on the Branch2 router.
C. The static route points to the tunnel0 interface that is misconfigured on the Branch2 router.
D. The static route points to the tunnel0 interface that is misconfigured on the R2 router.
Answer: C
Q4. - (Topic 8)
What is the best way to verify that a host has a path to other hosts in different networks?
A. Ping the loopback address.
B. Ping the default gateway.
C. Ping the local interface address.
D. Ping the remote network.
Answer: D
Explanation:
Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, the ping command is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.
If you call ipconfig /all and receive a response, there is no need to ping the loopback address and your own IP address — Ipconfig has already done so in order to generate the report.
It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:
ping < IP address >
Perform the following steps when using Ping:
✑ Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.
ping 127.0.0.1
If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.
✑ Ping the IP address of the local computer to verify that it was added to the network
correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.
ping < IP address of local host >
✑ Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.
ping < IP address of default gateway >
✑ Ping the IP address of a remote host to verify that you can communicate through a router.
ping < IP address of remote host >
✑ Ping the host name of a remote host to verify that you can resolve a remote host name.
ping < Host name of remote host >
✑ Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.
pathping < IP address of remote host >
Q5. - (Topic 5)
Which two are features of IPv6? (Choose two.)
A. anycast
B. broadcast
C. multicast
D. podcast
E. allcast
Answer: A,C
Explanation:
IPv6 addresses are classified by the primary addressing and routing methodologies common in networking: unicast addressing, anycast addressing, and multicast addressing.
✑ A unicast address identifies a single network interface. The Internet Protocol
delivers packets sent to a unicast address to that specific interface.
✑ An anycast address is assigned to a group of interfaces, usually belonging to different nodes. A packet sent to an anycast address is delivered to just one of the member interfaces, typically the nearest host, according to the routing protocol’s definition of distance. Anycast addresses cannot be identified easily, they have the same format as unicast addresses, and differ only by their presence in the network at multiple points. Almost any unicast address can be employed as an anycast address.
✑ A multicast address is also used by multiple hosts, which acquire the multicast address destination by participating in the multicast distribution protocol among the network routers. A packet that is sent to a multicast address is delivered to all interfaces that have joined the corresponding multicast group.
Q6. - (Topic 8)
Which command can you execute to set the user inactivity timer to 10 seconds?
A. SW1(config-line)#exec-timeout 0 10
B. SW1(config-line)#exec-timeout 10
C. SW1(config-line)#absolute-timeout 0 10
D. SW1(config-line)#absolute-timeout 10
Answer: A
Q7. - (Topic 7)
What Netflow component can be applied to an interface to track IPv4 traffic?
A. flow monitor
B. flow record
C. flow sampler
D. flow exporter
Answer: A
Explanation:
Flow monitors are the Flexible NetFlow component that is applied to interfaces to perform network traffic monitoring. Flow monitors consist of a record and a cache. You add the record to the flow monitor after you create the flow monitor. The flow monitor cache is automatically created at the time the flow monitor is applied to the first interface. Flow data
is collected from the network traffic during the monitoring process based on the key and nonkey fields in the record, which is configured for the flow monitor and stored in the flow monitor cache.
For example, the following example creates a flow monitor named FLOW-MONITOR-1 and enters Flexible NetFlow flow monitor configuration mode:
Router(config)# flow monitor FLOW-MONITOR-1 Router(config-flow-monitor)#
Q8. - (Topic 8)
Which HSRP feature was new in HSRPv2?
A. VLAN group numbers that are greater than 255
B. virtual MAC addresses
C. tracking
D. preemption
Answer: A
Q9. - (Topic 4)
Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?
A. Router(config-if)# ppp authentication chap fallback ppp
B. Router(config-if)# ppp authentication chap pap
C. Router(config-if)# authentication ppp chap fallback ppp
D. Router(config-if)# authentication ppp chap pap
Answer: B
Explanation:
This command tells the router first to use CHAP and then go to PAP if CHAP isn't available.
Q10. - (Topic 3)
Refer to the exhibit.
C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
A. These commands need to be added to the configuration: C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration: C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration: C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.