Exambible ccna 200 125 pdf Questions are updated and all 200 125 ccna pdf answers are verified by experts. Once you have completely prepared with our ccna routing and switching 200 125 official cert guide library exam prep kits you will be ready for the real 200 125 cisco exam without a problem. We have Improve Cisco ccna routing and switching 200 125 dumps study guide. PASSED 200 125 ccna v3 0 First attempt! Here What I Did.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. DRAG DROP - (Topic 3)
Drag the Cisco default administrative distance to the appropriate routing protocol or route. (Not all options are used.)
Answer:
Q2. - (Topic 8)
If the primary root bridge experiences a power loss, which switch takes over?
A. switch 0004.9A1A.C182
B. switch 00E0.F90B.6BE3
C. switch 00E0.F726.3DC6
D. switch 0040.0BC0.90C5
Answer: A
Q3. - (Topic 8)
Refer to the exhibit.
What is the effect of the given configuration?
A. It configures an inactive switch virtual interface.
B. It configures an active management interface.
C. It configures the native VLAN.
D. It configures the default VLAN.
Answer: A
Q4. - (Topic 3)
A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task?
A. service password-encryption
access-list 1 permit 192.168.1.0 0.0.0.255
line vty 0 4 login
password cisco access-class 1
B. enable password secret line vty 0
login
password cisco
C. service password-encryption line vty 1
login
password cisco
D. service password-encryption line vty 0 4
login
password cisco
Answer: C
Explanation:
Only one VTY connection is allowed which is exactly what's requested. Incorrect Answer: command.
line vty0 4
would enable all 5 vty connections.
Topic 4, WAN Technologies
Q5. - (Topic 8)
Which command can you enter to determine whether a switch is operating in trunking mode?
A. show ip interface brief
B. show vlan
C. show interfaces
D. show interface switchport
Answer: D
Q6. - (Topic 8)
Which destination IP address can a host use to send one message to multiple devices across different subnets?
A. 172.20.1.0
B. 127.0.0.1
C. 192.168.0.119
D. 239.255.0.1
Answer: D
Explanation: Multicast is a networking protocol where one host can send a message to a special multicast IP address and one or more network devices can listen for and receive those messages.
Multicast works by taking advantage of the existing IPv4 networking infrastructure, and it does so in something of a weird fashion. As you read, keep in mind that things are a little
confusing because multicast was "shoe-horned" in to an existing technology.
For the rest of this article, let's use the multicast IP address of 239.255.0.1. We'll not worry about port numbers yet, but make a mental note that they are used in multicast. We'll discuss that later.
Q7. - (Topic 3)
What OSPF command, when configured, will include all interfaces into area 0?
A. network 0.0.0.0 255.255.255.255 area 0
B. network 0.0.0.0 0.0.0.0 area 0
C. network 255.255.255.255 0.0.0.0 area 0
D. network all-interfaces area 0
Answer: A
Explanation:
Example 3-1 displays OSPF with a process ID of 1 and places all interfaces configured with an IP address in area 0. The network command network 0.0.0.0 255.255.255.255 area 0 dictates that you do not care (255.255.255.255) what the IP address is, but if an IP address is enabled on any interface, place it in area 0.
Example 3-1 Configuring OSPF in a Single Area
router ospf 1
network 0.0.0.0 255.255.255.255 area 0
Reference: http://www.ciscopress.com/articles/article.asp?p=26919&seqNum=3
Q8. - (Topic 5)
What levels will be trapped if the administrator executes the command router(config)# logging trap 4 (Choose four)
A. Emergency
B. Notice
C. Alert
D. Error
E. Warning
Answer: A,C,D,E
Explanation:
The Message Logging is divided into 8 levels as listed below: Level Keyword Description
0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist
3 errors Error conditions exist
4 warnings Warning conditions exist
5 notification Normal, but significant, conditions exist 6 informational Informational messages
7 debugging Debugging messages
If you specify a level with the “logging trap level” command, that level and all the higher levels will be logged. For example, by using the “logging trap 4 command, all the logging of emergencies, alerts, critical, errors, warnings will be logged.
Q9. - (Topic 4)
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?
A. defines the destination IP address that is used in all broadcast packets on DCLI 202
B. defines the source IP address that is used in all broadcast packets on DCLI 202
C. defines the DLCI on which packets from the 192.168.1.2 IP address are received
D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address
Answer: D
Explanation:
This command identifies the DLCI that should be used for all packets destined to the 192.168.1.2 address. In this case, DLCI 202 should be used.
Q10. - (Topic 8)
A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?
A. the EIGRP route
B. the OSPF route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Answer: A