Proper study guides for Replace Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certified begins with Cisco 200 125 ccna book preparation products which designed to deliver the Download ccna 200 125 book questions by making you pass the 200 125 ccna v3 0 test at your first time. Try the free cisco ccna 200 125 demo right now.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. - (Topic 5)
Which three features are added in SNMPv3 over SNMPv2?
A. Message Integrity
B. Compression
C. Authentication
D. Encryption
E. Error Detection
Answer: A,C,D
Explanation:
Cisco IOS software supports the following versions of SNMP:
+ SNMPv1 – The Simple Network Management Protocol: A Full Internet Standard, defined in RFC 1157. (RFC 1157 replaces the earlier versions that were published as RFC 1067 and RFC 1098.) Security is based on community strings.
+ SNMPv2c – The community-string based Administrative Framework for SNMPv2. SNMPv2c (the “c” stands for “community”) is an Experimental Internet Protocol defined in RFC 1901, RFC 1905, and RFC 1906. SNMPv2c is an update of the protocol operations and data types of SNMPv2p (SNMPv2 Classic), and uses the community-based security model of SNMPv1.
+ SNMPv3 – Version 3 of SNMP. SNMPv3 is an interoperable standards-based protocol defined in RFCs 2273 to 2275. SNMPv3 provides secure access to devices by a combination of authenticating and encrypting packets over the network. The security features provided in SNMPv3 are as follows:
– Message integrity: Ensuring that a packet has not been tampered with in transit.
– Authentication: Determining that the message is from a valid source.
– Encryption: Scrambling the contents of a packet prevent it from being learned by an unauthorized source.
Q2. - (Topic 3)
Refer to the exhibit.
The speed of all serial links is E1 and the speed of all Ethernet links is 100 Mb/s. A static route will be established on the Manchester router to direct traffic toward the Internet over the most direct path available. What configuration on the Manchester router will establish a route toward the Internet for traffic that originates from workstations on the Manchester LAN?
A. ip route 0.0.0.0 255.255.255.0 172.16.100.2
B. ip route 0.0.0.0 0.0.0.0 128.107.1.1
C. ip route 0.0.0.0 255.255.255.252 128.107.1.1
D. ip route 0.0.0.0 0.0.0.0 172.16.100.1
E. ip route 0.0.0.0 0.0.0.0 172.16.100.2
F. ip route 0.0.0.0 255.255.255.255 172.16.100.2
Answer: E
Explanation:
We use default routing to send packets with a remote destination network not in the routing table to the next-hop router. You should generally only use default routing on stub networks—those with only one exit path out of the network.
According to exhibit, all traffic towards Internet that originates from workstations should forward to Router R1.
Syntax for default route is:
ip route <Remote_Network> <Netmask> <Next_Hop_Address>.
Q3. - (Topic 4)
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
Answer: D
Explanation:
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are marked as discard eligible (DE) which means they can be dropped if the congestion occurs within the Frame Relay network.
Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit that is used to identify frames that are first to be dropped when the CIR is exceeded.
Q4. - (Topic 8)
What is the danger of the permit any entry in a NAT access list?
A. It can lead to overloaded resources on the router.
B. It can cause too many addresses to be assigned to the same interface.
C. It can disable the overload command.
D. It prevents the correct translation of IP addresses on the inside network.
Answer: A
Q5. - (Topic 8)
Scenario:
You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.
Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.
NAT is enabled on router R1.
The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.
R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.
You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.
Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office. Which statement correctly identifies the problem on Router R1?
A. Interesting traffic for NAT ACL is incorrectly configured.
B. NAT configurations on the interfaces are incorrectly configured
C. NAT translation statement incorrectly configured.
D. Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.
Answer: B
Q6. - (Topic 8)
Which logging command can enable administrators to correlate syslog messages with millisecond precision?
A. no logging console
B. logging buffered 4
C. no logging monitor
D. service timestamps log datetime msec
E. logging host 10.2.0.21
Answer: D
Q7. - (Topic 3)
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
Answer: B,D
Explanation:
Here is a list of the differences between OSPFv2 and OSPFv3:
✑ They use different address families (OSPFv2 is for IPv4-only, OSPFv3 can be used for IPv6-only or both protocols
✑ OSPFv3 introduces new LSA types
✑ OSPFv3 has different packet format
✑ OSPFv3 uses different flooding scope bits (U/S2/S1)
✑ OSPFv3 adjacencies are formed over link-local IPv6 communications
✑ OSPFv3 runs per-link rather than per-subnet
✑ OSPFv3 supports multiple instances on a single link, Interfaces can have multiple IPv6 addresses
✑ OSPFv3 uses multicast addresses FF02::5 (all OSPF routers), FF02::6 (all OSPF DRs)
✑ OSPFv3 Neighbor Authentication done with IPsec (AH)
✑ OSPFv2 Router ID (RID) must be manually configured, still a 32-bit number
Reference: http://www.networkworld.com/article/2225270/cisco-subnet/ospfv3-for-ipv4-and- ipv6.html
Q8. - (Topic 3)
Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth
B. Bandwidth and Delay
C. Bandwidth, Delay, and MTU
D. Bandwidth, MTU, Reliability, Delay, and Load
Answer: A
Explanation:
The well-known formula to calculate OSPF cost is Cost = 108 / Bandwidth
Q9. - (Topic 7)
What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?
A. SNMP
B. Netflow
C. WCCP
D. IP SLA
Answer: B
Explanation:
Netflow can be used to diagnose slow network performance, bandwidth hogs and bandwidth utilization quickly with command line interface or reporting tools.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios- netflow/prod_white_paper0900aecd80406232.html
Q10. - (Topic 8)
Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Answer: B,C
Explanation:
A loopback interface never comes down even if the link is broken so it provides stability for the OSPF process (for example we use that loopback interface as the router-id) -
The router-ID is chosen in the order below:
+ The highest IP address assigned to a loopback (logical) interface.+ If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen.
-> The loopback interface will be chosen as the router ID of RouterB –