Pinpoint of ccna wireless 200 355 official cert guide training materials and item pool for Cisco certification for client, Real Success Guaranteed with Updated ccna wireless 200 355 dumps pdf dumps vce Materials. 100% PASS Implementing Cisco Wireless Network Fundamentals exam Today!


2026 New 200-355 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-355/

Q1. The administrator has noticed that the configuration on a controller is different than in Cisco WCS. How can the administrator fix this issue? 

A. The configuration can be copied from the controller to the Cisco WCS or from the WCS to the controller. 

B. The configuration can be copied only from the Cisco WCS to the controller. 

C. The configuration can be copied only from the controller to the Cisco WCS. 

D. The controller must be removed from the Cisco WCS and then added again. 

Answer: A 

Q2. Which four options are the characteristics of the original 802.11 protocol? (Choose four.) 

A. Defined DSSS and FHSS as possible methods for modulation 

B. Designed to operate in the 5 GHz ISM frequency spectrum 

C. The most common deployment is three non-overlapping channels that are 20 MHz wide 

D. The protocol sets the maximum throughput at 1 Mb/s or 2 Mb/s 

E. Defined FHSS and OFDM as possible methods for modulation 

F. The most common deployment is three non-overlapping channels that are 22 MHz wide 

G. Designed to operate in the 2.4 GHz ISM frequency spectrum 

H. The protocol sets the maximum throughput at 1 Mb/s 

Answer: A,D,F,G 

Q3. Which four parameters must be configured for local EAP-FAST on the controller? (Choose four.) 

A. authority ID 

B. authority ID Information 

C. client key 

D. PAC 

E. server key 

F. TTL for PAC 

G. monitor key 

H. NTP source 

Answer: A,B,E,F 

Q4. RAG DROP 

Answer:  

Q5. The introduction of consumer phones and tablets into enterprise WLANs can have an impact on 802.11a/b/g/n deployments. The Apple iPhone 4 and iPad 2 are very common examples. 

Which statement best describes the abilities of these devices? 

A. The Apple iPhone 4 and the iPad 2 use 2.4 GHz and 5 GHz. The Apple iPhone 4 uses only one spatial stream and the iPad 2 uses two spatial streams. 

B. The Apple iPhone 4 uses only 2.4 GHz and the iPad 2 only uses 5 GHz. The Apple iPhone 4 uses only one spatial stream and the iPad 2 uses two spatial streams. 

C. The Apple iPhone 4 uses 2.4 GHz and the iPad 2 uses 2.4 GHz or 5 GHz. The Apple iPhone 4 only uses one spatial stream and the iPad 2 uses two spatial streams. 

D. The Apple iPhone 4 uses 2.4 GHz and the iPad 2 uses 2.4 GHz or 5 GHz. The Apple iPhone 4 and the iPad 2 use only one spatial stream. 

Answer: D 

Q6. The network administrator has used VLANs to separate VoIP frames from data frames in the wired network. What must the administrator use to separate those frames in the wireless network? 

A. multiple SSIDs 

B. multiple authentications 

C. multiple WEP or WPA keys 

D. multiple channels 

E. multiple 802.11 radios (a, b, g, n) 

Answer: A 

Q7. Refer to the exhibit. A customer is using central web authentication with a Cisco 5508 Wireless Controller and Cisco Identity Services Engine. An error occurs when wireless clients are redirected to the hosted splash page. What is causing the client error? 

A. Secure Web Mode is disabled on the WLC. 

B. OCSP is disabled on the WLC. 

C. Management Via Dynamic Interface is disabled on the WLC. 

D. Ethernet Multicast Forwarding is enabled on the WLC. 

Answer: A 

Q8. A customer wants to deploy a mesh network with 2 root access points and 10 mesh access points. The root access points should be configured as which mode on the WLC? 

A. mesh 

B. FlexConnect 

C. bridge 

D. rouge detection 

E. sniffer 

Answer: C 

Q9. A network engineer in the GUI of WCS version 7 wants to add an autonomous access point. Where can this command be found in the drop-down menu? 

A. Configure > Access Point > Add Autonomous APs 

B. Manage > Access Points > Add Autonomous APs 

C. Administration > Access Point > Add Autonomous APs 

D. Location > Access Point > Add Autonomous APs 

Answer: A 

Q10. Refer to the exhibit. 

A customer has enabled the primary DNS server to return the correct controller IP address in response to a CISCO-CAPWAP-CONTROLLER.localdomain request coming from new access points associating to the wireless network. The access points seem to still be receiving the wrong IP address and cannot associate to the primary controller. 

Why are the access points receiving the wrong IP information? 

A. The DHCP option 43 has an incorrect controller IP address configured. 

B. The DNS server must be configured to respond to CISCO-LWAPP-CONTROLLER.localdomain request. 

C. The controller and wireless action point need to be Layer 2 adjacent. 

D. The controller must be configured for DHCP option 15 request. 

Answer: A