All About Tested 200-355 exam dumps

Q5. Which two statements about the results of the Cisco WCS version 7.0 client troubleshooting tool are true? (Choose two.)

A. Results of Layers 1 - 3 are provided.

B. Results of only Layers 2 and 3 are provided.

C. Results of Layers 4 - 7 are provided.

D. The tabulated results vary depending on the client type.

E. Results are provided in a fixed four-part tabulation.

F. Results are provided in a fixed six-part tabulation.

View Answer

Q6. Refer to the exhibit.

A wireless network that consists of Cisco Aironet 1260 APs and Cisco 2100 Series WLC has been correctly configured with Cisco WCS version 7, which is also used for management. The CleanAir Zone of Impact is not visible for the respective Cisco WCS maps.

Which two issues are causing the problem? (Choose two.)

A. software version

B. AP

C. Cisco WLC

D. Cisco MSE

E. Cisco WCS

F. Cisco WCS is not enabled.

View Answer

Q7. What are two modules of the CCX Lite program? (Choose two.)

A. foundation

B. voice

C. RF power

D. roaming

View Answer

Q8. A customer is deploying the Cisco 5508 Wireless Controller in a unified wireless solution. Which command must be configured on the neighboring switch port if the management interface on the WLC is configured to send untagged traffic to ensure that management traffic utilizes VLAN 10?

A. switchport trunk native vlan 10

B. spanning-tree portfast

C. switchport trunk allowed vlan 10

D. channel-group 10

View Answer

Q9. Which three statements must be true for Cisco WLC to support roaming? (Choose three.)

A. Controllers are in the same mobility group.

B. Controllers operate in different LWAPP modes.

C. ACLs are the same.

D. Virtual interface IP addresses are the same.

E. Controllers have different versions of code.

F. Controllers need to have the same hostname.

View Answer

Q10. When reading a radiation pattern for an antenna, at which two drops in signal and power is the beamwidth measured? (Choose two.)

A. 3 dB

B. 6 dB

C. 9 dB

D. 10 dB

E. 1/2 power

F. 1/4 power

G. 1/8 power

H. 1/10 power

View Answer

Q11. What must be done for Cisco WLC and Cisco WCS to communicate?

A. The IP address and subnet mask of the Cisco WLC must be configured in the Cisco WCS.

B. The IP address and subnet mask of the Cisco WCS must be configured in the Cisco WLC.

C. The identity certificate of the Cisco WLC must be added to the Cisco WCS.

D. The Cisco WLC and Cisco WCS must exchange identity certificates.

View Answer

Q12. An engineer has been noticing the power settings on several of the office APs change from day to day ever since two more APs were installed. After logging into the WLC, the engineer verifies that the power levels on 4 of the 802.11n radios are fluctuating up and down. What is the reason for this?

A. The controller has the APs in H-REAP mode and are on a Layer 2 connection instead of Layer 3.

B. The RRM has revealed a bad survey and is attempting to power down some of the radios to make up for it.

C. The WLC has created temporary coverage holes while stepping through power levels for some of the APs.

D. Several APs have high levels of overlapping coverage in the same area and the WLC is using RRM to correct the cell sizes AP coverage.

View Answer

Q13. Which architecture is used to divide the roles between the access point and the WLC when deploying a centralized wireless solution?

A. Split MAC

B. CAPWAP

C. LWAPP

D. Local MAC

View Answer

Q14. What three components are required to configure Mobility Group Members between Wireless LAN Controllers? (Choose three.)

A. Controller Management IP Address

B. Controller Virtual IP Address

C. Controller Multicast IP Address

D. Controller MAC Address

E. Controller Mobility Group Name

F. Controller AP Management IP Address

G. Controller RF Group Name

View Answer