It is more faster and easier to pass the Cisco 300 075 vce exam by using 100% Guarantee Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) questuins and answers. Immediate access to the Latest 300 075 vce Exam and find the same core area 300 075 ciptv2 questions with professionally verified answers, then PASS your exam with a high score now.


2026 New 300-075 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-075/

Q1. Which option configures call preservation for H.323-based SRST mode? 

A. voice service voip h323 call preserve 

B. call preservation not possible with H.323 

C. call-manager-fallback preserve-call 

D. dial-peer voice 1 voip call preserve 

Answer: A 

Q2. Refer to the exhibit. 

When a call between two HQ users is being conferenced with a remote user at BR, which configuration is needed? 

A. The BR_MRG must contain the transcoder device. The BR_MRGL must be assigned to the BR phones. 

B. The HQ_MRG must contain the transcoder device. The HQ_MRGL must be assigned to the HQ phones. 

C. A transcoder should be configured at the remote site and assigned to all remote phones through the BR_MRGL. 

D. The HQ_MRG must contain the transcoder device. The HQ_MRGL must be assigned to the software conference bridge. 

E. Enable the software conference bridge to support the G.711 and G.729 codecs in Cisco Unified Communications Manager Service Parameters. 

Answer: D 

Q3. Which task must you perform before deleting a transcoder? 

A. Delete the dependency records. 

B. Unassign it from a media resource group. 

C. Use the Reset option. 

D. Remove the device pool. 

E. Remove the subunit. 

F. Delete the common device configuration. 

Answer: B 

Q4. Which action configures CAC utilizing only Cisco Unified Communications Manager software? 

A. Configure Cisco Unified Communications Manager regions. 

B. Configure Cisco Unified Communications Manager locations. 

C. Configure Cisco Unified Communications Manager RSVP-enabled locations. 

D. Configure Cisco Unified Communications Manager MTPs. 

Answer: B 

Q5. Refer to the exhibit. 

How many calls can be placed to Cluster B? 

A. three G.729 calls 

B. one G.711 call 

C. one G.711 and three G.729 calls 

D. There is no limit for incoming calls to Cluster B. Outgoing calls are limited to one G.711 and three G.729 calls. 

Answer: A 

Q6. When using Cisco Unified Communications Manager Express in SRST mode, how many multicast music on hold streams can be utilized by the system at any given time? 

A. 3 

B. 6 

C. 2 

D. 4 

E. 1 

F. 5 

Answer: B 

Q7. When an incoming PSTN call arrives at an H.323 gateway, how does the called number get normalized to an internal directory number in Cisco Unified Communications Manager? 

A. Normalization is done by configuring the significant digits for inbound calls on the H.323 gateway configuration in Cisco Unified Communications Manager. 

B. Normalization is done using route patterns. 

C. Normalization is done using the gateway incoming calling party prefixes based on number type. 

D. Normalization is achieved by local route group that is assigned to the H.323 gateway. 

Answer: A 

Q8. When an H.323 trunk is added for Call Control Discovery, which statement is true? 

A. The H.323 trunk is added by selecting Inter-Cluster Trunk (Non-Gatekeeper Controlled) and Device Protocol Inter-Cluster Trunk. The Enable SAF check box should be selected in the trunk configuration. 

B. The H.323 trunk is added by selecting Inter-Cluster Trunk (Non-Gatekeeper Controlled) and Device Protocol Inter-Cluster Trunk. The Trunk Service Type should be Call Control Discovery. 

C. The H.323 trunk is added by selecting Call Control Discovery Trunk and then selecting 

H.323 as the protocol to be used. 

D. The H.323 trunk is added by selecting H.323 Trunk, and selecting Inter-Cluster Trunk as the Device Protocol. The destination IP address field is configured as ‘SAF’ to indicate that this trunk is used for SAF. 

Answer: A 

Explanation: 

Reference. Implementing Cisco Unified Communications Manager Part 2 (CIPT2), Chapter3: Implementing Multisite Connections, pg 70-71, Fig 3-14 and Fig 3-15 

Q9. Scenario 

There are two call control systems in this item. The Cisco UCM is controlling the DX650, the Cisco Jabber for Windows Client, and the 9971 Video IP Phone. The Cisco VCS is controlling the SX20, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows. 

Use the exhibits to answer the following questions. 

SX20 System Information 

DX650 Configuration 

MRGL 

DP 

Locations 

AARG 

CSS 

Movi Failure 

Movi Settings 

A new DX650 IP phone with MAC address D0C7.8914.132D, IP address is 172.18.32.119 has been added to the Cisco Unified Communications Manager, but is not registering properly. 

What is causing this failure? 

A. Device Pool cannot be default. 

B. The DX650 is the incorrect calling search space. 

C. The DX650 Phones does not support SIP. 

D. The location Hub_None has not been activated. 

E. The DX650’s MAC address is incorrect in the Cisco UCM. 

Answer: E 

Explanation: 

From the screen capture below we can see that the DX650 phone’s MAC address was incorrectly entered as D0C78914131D, not D0C78914132D. 

Q10. Scenario 

There are two call control systems in this item. The Cisco UCM is controlling the Cisco Jabber for Windows Client, and the 7965 and 9971 Video IP Phone. The Cisco VCS is controlling the SX20, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows. 

Use the exhibits to answer the following questions. 

DP 

Locations 

CSS 

Movi Failure 

Movi Settings 

CIPTV Topo 

Subzone 

Links 

Pipe 

Both of the Cisco TelePresence Video for Windows clients are able to log into the server but can’t make any calls. After reviewing the exhibits, which of the following reasons could be causing this failure? 

A. Wrong username and/or password. 

B. Wrong SIP domain name. 

C. The TMSPE is not working. 

D. The bandwidth is incorrectly configured. 

Answer: D