Ucertify cisco 300 206 Questions are updated and all 300 206 senss answers are verified by experts. Once you have completely prepared with our 300 206 senss pdf exam prep kits you will be ready for the real 300 206 dumps exam without a problem. We have Leading Cisco 300 206 dumps dumps study guide. PASSED 300 206 dumps First attempt! Here What I Did.


2026 New 300-206 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-206/

Q1. Refer to the exhibit. 

Which option describes the expected result of the capture ACL? 

A. The capture is applied, but we cannot see any packets in the capture 

B. The capture does not get applied and we get an error about mixed policy. 

C. The capture is applied and we can see the packets in the capture 

D. The capture is not applied because we must have a host IP as the source 

Answer: B 

Q2. Which tool provides the necessary information to determine hardware lifecycle and compliance details for deployed network devices? 

A. Prime Infrastructure 

B. Prime Assurance 

C. Prime Network Registrar 

D. Prime Network Analysis Module 

Answer: A 

Q3. An attacker has gained physical access to a password protected router. Which command will prevent access to the startup-config in NVRAM? 

A. no service password-recovery 

B. no service startup-config 

C. service password-encryption 

D. no confreg 0x2142 

Answer: A 

Q4. Which two SNMPv3 features ensure that SNMP packets have been sent securely?" Choose two. 

A. host authorization 

B. authentication 

C. encryption 

D. compression 

Answer: B,C 

Q5. Which option is the default logging buffer size In memory of the Cisco ASA adaptive security appliance? 

A. 8KB 

B. 32KB 

C. 2KB 

D. 16KB 

E. 4KB 

Answer: E 

Explanation: 

http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_gen eral_c onfig/ monitor_syslog.html 

Q6. Which action is considered a best practice for the Cisco ASA firewall? 

A. Use threat detection to determine attacks 

B. Disable the enable password 

C. Disable console logging D. Enable ICMP permit to monitor the Cisco ASA interfaces 

E. Enable logging debug-trace to send debugs to the syslog server 

Answer: A 

Q7. According to the logging configuration on the Cisco ASA, what will happen if syslog server 10.10.2.40 fails? 

A. New connections through the ASA will be blocked and debug system logs will be sent to the internal buffer. 

B. New connections through the ASA will be blocked and informational system logs will be sent to the internal buffer. 

C. New connections through the ASA will be blocked and system logs will be sent to server 10.10.2.41. 

D. New connections through the ASA will be allowed and system logs will be sent to server 10.10.2.41. 

E. New connections through the ASA will be allowed and informational system logs will be sent to the internal buffer. 

F. New connections through the ASA will be allowed and debug system logs will be sent to the internal buffer. 

Answer: B 

Explanation: 

This is shown by the following screen shot: 

\psfHomeDesktopScreen Shot 2015-06-17 at 5.26.32 PM.png 

Q8. Which statement about traffic storm control behavior is true? 

A. Traffic storm control cannot determine if the packet is unicast or broadcast. 

B. If you enable broadcast and multicast traffic storm control and the combined broadcast and multicast traffic exceeds the level within a 1 second traffic storm interval, storm control drops all broadcast and multicast traffic until the end of the storm interval 

C. Traffic storm control uses the Individual/Group bit in the packet source address to determine if the packet is unicast or broadcast. 

D. Traffic storm control monitors incoming traffic levels over a 10 second traffic storm control interval 

Answer: B 

Q9. When a Cisco ASA is configured in multicontext mode, which command is used to change between contexts? 

A. changeto config context 

B. changeto context 

C. changeto/config context change 

D. changeto/config context 2 

Answer: B 

Q10. You have installed a web server on a private network. Which type of NAT must you implement to enable access to the web server for public Internet users? 

A. static NAT 

B. dynamic NAT 

C. network object NAT 

D. twice NAT 

Answer: A