Master the 300-209 Implementing Cisco Secure Mobility Solutions (SIMOS) content and be ready for exam day success quickly with this Testking 300-209 torrent. We guarantee it!We make it a reality and give you real 300-209 questions in our Cisco 300-209 braindumps.Latest 100% VALID Cisco 300-209 Exam Questions Dumps at below page. You can use our Cisco 300-209 braindumps and pass your exam.
2026 New 300-209 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-209/
Q1. What does NHRP stand for?
A. Next Hop Resolution Protocol
B. Next Hop Registration Protocol C. Next Hub Routing Protocol
D. Next Hop Routing Protocol
Answer: A
Q2. Which group-policy subcommand installs the Diagnostic AnyConnect Report Tool on user computers when a Cisco AnyConnect user logs in?
A. customization value dart
B. file-browsing enable
C. smart-tunnel enable dart
D. anyconnect module value dart
Answer: D
Q3. A user is unable to establish an AnyConnect VPN connection to an ASA. When using the Real-Time Log viewer within ASDM to troubleshoot the issue, which two filter options would the administrator choose to show only syslog messages relevant to the VPN connection? (Choose two.)
A. Client's public IP address
B. Client's operating system
C. Client's default gateway IP address
D. Client's username
E. ASA's public IP address
Answer: A,D
Q4. Which three configurations are prerequisites for stateful failover for IPsec? (Choose three.)
A. Only the IKE configuration that is set up on the active device must be duplicated on the standby device; the IPsec configuration is copied automatically.
B. Only crypto map configuration that is set up on the active device must be duplicated on the standby device.
C. The IPsec configuration that is set up on the active device must be duplicated on the standby device.
D. The active and standby devices can run different versions of the Cisco IOS software but need to be the same type of device.
E. The active and standby devices must run the same version of the Cisco IOS software and should be the same type of device.
F. Only the IPsec configuration that is set up on the active device must be duplicated on the standby device; the IKE configuration is copied automatically.
G. The IKE configuration that is set up on the active device must be duplicated on the standby device.
Answer: C,E,G
Q5. Refer to the exhibit.
The customer needs to launch AnyConnect in the RDP machine. Which configuration is correct?
A. crypto vpn anyconnect profile test flash:RDP.xml
policy group default
svc profile test
B. crypto vpn anyconnect profile test flash:RDP.xml
webvpn context GW_1
browser-attribute import flash:/swj.xml
C. crypto vpn anyconnect profile test flash:RDP.xml
policy group default
svc profile flash:RDP.xml
D. crypto vpn anyconnect profile test flash:RDP.xml
webvpn context GW_1
browser-attribute import test
Answer: A
Q6. What is the default topology type for a GET VPN?
A. point-to-point
B. hub-and-spoke
C. full mesh
D. on-demand spoke-to-spoke
Answer: C
Q7. The Cisco AnyConnect client fails to connect via IKEv2 but works with SSL. The following error message is displayed:
"Login Denied, unauthorized connection mechanism, contact your administrator"
What is the most possible cause of this problem?
A. DAP is terminating the connection because IKEv2 is the protocol that is being used.
B. The client endpoint does not have the correct user profile to initiate an IKEv2 connection.
C. The AAA server that is being used does not authorize IKEv2 as the connection mechanism.
D. The administrator is restricting access to this specific user.
E. The IKEv2 protocol is not enabled in the group policy of the VPN headend.
Answer: E
Q8. To change the title panel on the logon page of the Cisco IOS WebVPN portal, which file must you configure?
A. Cisco IOS WebVPN customization template
B. Cisco IOS WebVPN customization general
C. web-access-hlp.inc
D. app-access-hlp.inc
Answer: A
Q9. In the Cisco ASDM interface, where do you enable the DTLS protocol setting?
A. Configuration > Remote Access VPN > Network (Client) Access > Group Policies > Add or Edit > Add or Edit Internal Group Policy
B. Configuration > Remote Access VPN > Network (Client) Access > AAA Setup > Local Users > Add or Edit
C. Device Management > Users/AAA > User Accounts > Add or Edit > Add or Edit User Account > VPN Policy > SSL VPN Client
D. Configuration > Remote Access VPN > Network (Client) Access > Group Policies > Add or Edit
Answer: C
Reference:
http://www.cisco.com/c/en/us/td/docs/security/vpn_client/anyconnect/anyconnect20/admini strative/guide/admin/admin5.html
Shows where DTLS can be configured as:
. Configuration > Remote Access VPN > Network (Client) Access > Group Policies > Add or Edit > Add or Edit Internal Group Policy > Advanced > SSL VPN Client
. Configuration > Remote Access VPN > Network (Client) Access > AAA Setup > Local Users > Add or Edit > Add or Edit User Account > VPN Policy > SSL VPN Client
.Device Management > Users/AAA > User Accounts > Add or Edit > Add or Edit User Account > VPN Policy > SSL VPN Client
Q10. What is the default storage location of user-level bookmarks in an IOS clientless SSL VPN?
A. disk0:/webvpn/{context name}/
B. disk1:/webvpn/{context name}/
C. flash:/webvpn/{context name}/
D. nvram:/webvpn/{context name}/
Answer: C