Avant-garde 300-410 Free Samples For Implementing Cisco Enterprise Advanced Routing And Services (ENARSI) Certification

NEW QUESTION 1
Which command displays the IP routing table information that is associated with VRF-Lite?

• A. show ip vrf
• B. show ip route vrf
• C. show run vrf
• D. show ip protocols vrf

Answer: B

NEW QUESTION 2
Which statement about MPLS LDP router ID is true?

• A. If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.
• B. The loopback with the highest IP address is selected as the router ID.
• C. The MPLS LDP router ID must match the IGP router ID.
• D. The force keyword changes the router ID to the specified address without causing any impact.

Answer: B

NEW QUESTION 3
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

• A. R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
• B. R1 does not accept any routes other than 192.168.130.0/24
• C. R1 does not forward traffic that is destined for 192.168.30.0/24
• D. Network 192.168.130.0/24 is not allowed in the R1 table

Answer: A

NEW QUESTION 4
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?

• A. sudo maglev-config update
• B. sudo maglev install config update
• C. sudo maglev reinstall
• D. sudo update config install

Answer: A

NEW QUESTION 5
Refer to the exhibit.

ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to
achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?

• A. Start-time 00:00
• B. Start-time 0
• C. Start-time immediately
• D. Start-time now

Answer: D

NEW QUESTION 6
Refer to the exhibit.

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the
configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

• A. Use an extended access list instead of a standard access list.
• B. Change sequence 10 in the route-map command from permit to deny.
• C. Use a prefix list instead of an access list in the route map.
• D. Add this statement to the route map: route-map RM-OSPF-DL deny 20.

Answer: B

NEW QUESTION 7
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 8
Which transport layer protocol is used to form LDP sessions?

• A. UDP
• B. SCTP
• C. TCP
• D. RDP

Answer: C

NEW QUESTION 9
Refer to the exhibit.

An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?

• A. By default, only internal routes and external type 1 routes are redistributed into BGP
• B. Only classful networks are redistributed from OSPF to BGP
• C. BGP convergence is slow, so the route will eventually be present in the BGP table
• D. By default, only internal OSPF routes are redistributed into BGP

Answer: A

NEW QUESTION 10
Refer to the exhibit.

After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot
reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?

• A. Set the administrative distance 100 under the RIP process on R2.
• B. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
• C. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
• D. Redistribute the directly connected interfaces on R2.

Answer: B

NEW QUESTION 11
Refer to the exhibit.

Why is the remote NetFlow server failing to receive the NetFlow data?

• A. The flow exporter is configured but is not used.
• B. The flow monitor is applied in the wrong direction.
• C. The flow monitor is applied to the wrong interface.
• D. The destination of the flow exporter is not reachable.

Answer: D

NEW QUESTION 12
Refer to the exhibit.

An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?

• A. The summary-address command is used only for summarizing prefixes between areas.
• B. The summary route is visible only in the OSPF database, not in the routing table.
• C. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
• D. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.

Answer: A

NEW QUESTION 13
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?

• A. service timestamps log uptime
• B. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00
• C. service timestamps log datetime localtime show-timezone
• D. clock calendar-valid

Answer: A

NEW QUESTION 14
Refer to the exhibit.

Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: A

NEW QUESTION 15
Drag and drop the packet types from the left onto the correct descriptions on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 16
Which statement about IPv6 RA Guard is true?

• A. It does not offer protection in environments where IPv6 traffic is tunneled.
• B. It cannot be configured on a switch port interface in the ingress direction.
• C. Packets that are dropped by IPv6 RA Guard cannot be spanned.
• D. It is not supported in hardware when TCAM is programmed.

Answer: A

NEW QUESTION 17
What is a prerequisite for configuring BFD?

• A. Jumbo frame support must be configured on the router that is using BFD.
• B. All routers in the path between two BFD endpoints must have BFD enabled.
• C. Cisco Express Forwarding must be enabled on all participating BFD endpoints.
• D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.

Answer: C

NEW QUESTION 18
Drag and drop the DHCP messages from the left onto the correct uses on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 19
Refer to the exhibit.

Why is user authentication being rejected?

• A. The TACACS+ server expects “user”, but the NT client sends “domain/user”.
• B. The TACACS+ server refuses the user because the user is set up for CHAP.
• C. The TACACS+ server is down, and the user is in the local database.
• D. The TACACS+ server is down, and the user is not in the local database.

Answer: D

NEW QUESTION 20
When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”.
What is the reason for the error?

• A. The template has an incorrect configuration.
• B. The software version of the template is different from the software version of the device.
• C. The changes to the template were not committed.
• D. The tag that was used to filter the templates does not match the device tag.

Answer: B

NEW QUESTION 21
......