Act now and download your Cisco 400 101 pdf test today! Do not waste time for the worthless Cisco ccie 400 101 dumps tutorials. Download Up to the immediate present Cisco CCIE Routing and Switching (v5.0) exam with real questions and answers and begin to learn Cisco 400 101 vce with a classic professional.
2026 New 400-101 Exam Dumps with PDF and VCE Free: https://www.surepassexam.com/400-101-exam-dumps.html
Q1. Which two Cisco IOS XE commands can install a subpackage onto a router? (Choose two.)
A. request platform software package install rp rpSlotNumber file fileURL
B. boot system flash bootflash:filename
C. copy sourceUrl destinationUrl
D. license install file storedLocationUrl
E. issu loadversion rp identifier file diskType imageFilename
F. config-register value
Answer: A,C
Explanation:
. Managing and Configuring a Consolidated Package Using the request platform software package install Command
In the following example, the request platform software package install command is used to upgrade a consolidated package running on RP 0. The force option, which forces the upgrade past any prompt (such as already having the same consolidated package installed), is used in this example.
Router# request platform software package install rp 0 file bootflash:asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin force
To upgrade a consolidated package on the Cisco ASR 1000 Series Routers using the copy command, copy the consolidated package into the bootflash: directory on the router using the copy command as you would on most other Cisco routers. After making this copy, configure the router to boot using the consolidated package file. In the following example, the consolidated package file is copied onto the bootflash: file system from TFTP. The config-register is then set to boot using boot system commands, and the boot system commands instruct the router to boot using the consolidated package stored in the bootflash: file system. The new configuration is then saved using the copy running-config startup-config command, and the system is then reloaded to complete the process.
Router# dir bootflash:
Directory of bootflash:/
11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found
86401 drwx 4096 Dec 4 2007 06:06:24 -08:00.ssh
14401 drwx 4096 Dec 4 2007 06:06:36 -08:00.rollback_timer
28801 drwx 4096 Mar 18 2008 17:31:17 -07:00.prst_sync
43201 drwx 4096 Dec 4 2007 04:34:45 -08:00.installer
13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz
928862208 bytes total (712273920 bytes free)
Router# copy tftp bootflash:
Address or name of remote host []? 172.17.16.81
Source filename []? /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin
Destination filename [asr1000rp1-adventerprisek9.02.01.00.122-33.XNA.bin]?
Reference: http://www.cisco.com/c/en/us/td/docs/routers/asr1000/configuration/guide/chassis/asrswcfg /Package_Management.html#78189
Q2. DRAG DROP
Drag each AF class on the left to its matching DSCP binary value on the right.
Answer:
Q3. DRAG DROP
Drag and drop the TACACS+ configuration command on the left to the correct function it performs on the right.
Answer:
Q4. Which statement about the feasibility condition in EIGRP is true?
A. The prefix is reachable via an EIGRP peer that is in the routing domain of the router.
B. The EIGRP peer that advertises the prefix to the router has multiple paths to the destination.
C. The EIGRP peer that advertises the prefix to the router is closer to the destination than the router.
D. The EIGRP peer that advertises the prefix cannot be used as a next hop to reach the destination.
Answer: C
Explanation:
The advertised metric from an EIGRP neighbor (peer) to the local router is called Advertised Distance (or reported distance) while the metric from the local router to that network is called Feasible Distance. For example, R1 advertises network 10.10.10.0/24 with a metric of 20 to R2. For R2, this is the advertised distance. R2 calculates the feasible distance by adding the metric from the advertised router (R1) to itself. So in this case the feasible distance to network 10.10.10.0/24 is 20 + 50 = 70.
Before a router can be considered a feasible successor, it must pass the feasibility condition rule. In short, the feasibility condition says that if we learn about a prefix from a neighbor, the advertised distance from that neighbor to the destination must be lower than our feasible distance to that same destination. Therefore we see the Advertised Distance always smaller than the Feasible Distance to satisfy the feasibility condition.
Q5. DRAG DROP
Answer:
Q6. Refer to the exhibit.
How can Router X in AS70000 peer with Router Y in AS65000, in case Router Y supports only 2-byte ASNs?
A. Router X should be configured with a remove-private-as command, because this will establish the peering session with a random private 2-byte ASN.
B. It is not possible. Router Y must be upgraded to an image that supports 4-byte ASN.
C. Router Y should be configured with a 4-byte AS using the local-as command.
D. Router X should be configured with a 2-byte AS using the local-as command.
Answer: D
Explanation:
Since router Y does not support 4-byte ASN,s it will not understand any AS numbers larger than 65535, so router X should use the local-as command on the peering statement to router Y to so that it sends in a 2-byte ASN to router Y.
Q7. Which two statements are true about VPLS? (Choose two.)
A. It can work over any transport that can forward IP packets.
B. It provides integrated mechanisms to maintain First Hop Resiliency Protocols such as HSRP, VRRP, or GLBP.
C. It includes automatic detection of multihoming.
D. It relies on flooding to propagate MAC address reachability information.
E. It can carry a single VLAN per VPLS instance.
Answer: D,E
Explanation:
VPLS relies on flooding to propagate MAC address reachability information. Therefore, flooding cannot be prevented.
VPLS can carry a single VLAN per VPLS instance. To multiplex multiple VLANs on a single instance, VPLS uses IEEE QinQ.
Reference: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-7000-series-switches/white_paper_c11-574984.html
Q8. Refer to the exhibit.
Which statement about this IP SLA is true?
A. The SLA must also have a schedule configured before it will start.
B. The TTL of the SLA packets is 10.
C. The SLA has a timeout of 3.6 seconds.
D. The SLA has a lifetime of 5 seconds.
Answer: A
Explanation:
When you configure an IP SLAs operation, you must schedule the operation to begin capturing statistics and collecting error information. You can schedule an operation to start immediately or to start at a certain month, day, and hour. You can use the pending option to set the operation to start at a later time. The pending option is an internal state of the operation that is visible through SNMP. The pending state is also used when an operation is a reaction (threshold) operation waiting to be triggered. You can schedule a single IP SLAs operation or a group of operations at one time. We can see in this output that the IP SLA is still in a pending trigger state.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/44sg/configuration/guide/Wrapper-44SG/swipsla.html
Q9. DRAG DROP
Drag each SNMP term on the left to the matching definition on the right.
Answer:
Q10. Refer to the exhibit.
Which two statements about this configuration are true? (Choose two.)
A. Pings from SW2 to SW1 fail because SW1 is pruning VLAN 10.
B. VLANs 10 and 200 are added to the SW2 allowed list on interface fa0/22.
C. Pings from SW2 to SW1 are successful.
D. Only VLAN 200 is added to the SW1 allowed list on interface fa0/22.
Answer: B,C