Our pass rate is high to 98.9% and the similarity percentage between our ccie 400 101 dumps study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco 400 101 ccie exam in just one try? I am currently studying for the Cisco 400 101 ccie exam. Latest Cisco passleader 400 101 Test exam practice questions and answers, Try Cisco 400 101 pdf Brain Dumps First.
2026 New 400-101 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/400-101/
Q1. Which measure does IS-IS use to avoid sending traffic with a wrong MTU configuration?
A. IS-IS does not protect from MTU mismatch.
B. MTU value is communicated in IS-IS Sequence Number PDUs (SNP), and IS-IS adjacency is not established if an MTU mismatch is detected.
C. IS-IS uses path MTU discovery as specified in RFC 1063.
D. IS-IS uses padding of hello packets to full MTU.
Answer: D
Explanation:
Intermediate System-to-Intermediate System (IS-IS) hellos are padded to the full maximum transmission unit (MTU) size. The benefit of padding IS-IS Hellos (IIHs) to the full MTU is that it allows for early detection of errors due to transmission problems with large frames or due to mismatched MTUs on adjacent interfaces.
Reference: http://www.cisco.com/c/en/us/support/docs/ip/integrated-intermediate-system-to-intermediate-system-is-is/47201-isis-mtu.html
Q2. Which two statements about TCP are true? (Choose two.)
A. TCP option must be divisible by 32.
B. It has a 16-bit window size.
C. Its maximum data offset is fifteen 32-bit words.
D. It has a 32-bit window size.
E. Its maximum data offset is ten 32-bit words.
F. It has a 32-bit checksum field.
Answer: B,C
Q3. Which multicast protocol uses source trees and RPF?
A. DVMRP
B. PIM sparse mode
C. CBT
D. mOSPF
Answer: A
Explanation:
DVMRP builds a parent-child database using a constrained multicast model to build a forwarding tree rooted at the source of the multicast packets. Multicast packets are initially flooded down this source tree. If redundant paths are on the source tree, packets are not forwarded along those paths. Forwarding occurs until prune messages are received on those parent-child links, which further constrains the broadcast of multicast packets.
Reference: DVMRP and dense-mode PIM use only source trees and use RPF as previously described.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3550/software/release/12-1_19_ea1/configuration/guide/3550scg/swmcast.html
Q4. Which two statements about the function of the stub feature in EIGRP are true? (Choose two.)
A. It stops the stub router from sending queries to peers.
B. It stops the hub router from sending queries to the stub router.
C. It stops the stub router from propagating dynamically learned EIGRP prefixes to the hub routers.
D. It stops the hub router from propagating dynamically learned EIGRP prefixes to the stub routers.
Answer: B,C
Explanation:
When using the EIGRP Stub Routing feature, you need to configure the distribution and remote routers to use EIGRP, and to configure only the remote router as a stub. Only specified routes are propagated from the remote (stub) router. The router responds to queries for summaries, connected routes, redistributed static routes, external routes, and internal routes with the message "inaccessible." A router that is configured as a stub will send a special peer information packet to all neighboring routers to report its status as a stub router. Without the stub feature, even after the routes that are sent from the distribution router to the remote router have been filtered or summarized, a problem might occur. If a route is lost somewhere in the corporate network, EIGRP could send a query to the distribution router, which in turn will send a query to the remote router even if routes are being summarized. If there is a problem communicating over the WAN link between the distribution router and the remote router, an EIGRP stuck in active (SIA) condition could occur and cause instability elsewhere in the network. The EIGRP Stub Routing feature allows a network administrator to prevent queries from being sent to the remote router.
Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/eigrpstb.html
Q5. Refer to the exhibit.
The two standalone chassis are unable to convert into a VSS. What can you do to correct the problem?
A. Set a different port channel number on each chassis.
B. Set a different virtual domain ID on each chassis.
C. Set the redundancy mode to rpr on both chassis.
D. Add two ports to the port channel group.
Answer: A
Q6. Refer to the exhibit.
Why is network 172.16.1.0/24 not installed in the routing table?
A. There is no ARP entry for 192.168.1.1.
B. The router cannot ping 192.168.1.1.
C. The neighbor 192.168.1.1 just timed out and BGP will flush this prefix the next time that the BGP scanner runs.
D. There is no route for 192.168.1.1 in the routing table.
Answer: D
Explanation:
Here we see that the next hop IP address to reach the 172.16.1.0 network advertised by the BGP peer is 192.168.1.1. However, the 192.168.1.1 IP is not in the routing table of R3 so it adds the route to the BGP table but marks it as inaccessible, as shown.
Q7. Which IPv6 tunneling type establishes a permanent link between IPv6 domains over IPv4?
A. IPv4-compatible tunneling
B. ISATAP tunneling
C. 6to4 tunneling
D. manual tunneling
Answer: D
Explanation:
A manually configured tunnel is equivalent to a permanent link between two IPv6 domains over an IPv4 backbone. The primary use is for stable connections that require regular secure communication between two edge routers or between an end system and an edge router, or for connection to remote IPv6 networks.
Reference: http://www.cisco.com/c/en/us/td/docs/ios/ipv6/configuration/guide/12_4t/ipv6_12_4t_book/i p6-tunnel.html
Q8. Which two actions can you take to recover an interface in a errdisable state? (Choose two.)
A. Enable UDLD on the switch.
B. Enable errdisable recovery on the switch.
C. Execute the shutdown command on the interface, followed by the no shutdown command.
D. Remove the related commands from the configuration and reenter them.
E. Enable loop guard on the switch.
Answer: B,C
Q9. Which two attributes were introduced with the Cisco IOS BGP 4-byte ASN feature? (Choose two.)
A. AS4_AGGREGATOR
B. AS4_PATH
C. AS4_PLAIN
D. AS4_DOT
E. AS4_TRANS
Answer: A,B
Q10. Which two 802.1D port states are expected in a stable Layer 2 network? (Choose two.)
A. forwarding
B. learning
C. listening
D. blocking
E. disabled
Answer: A,D