It is more faster and easier to pass the Cisco 400-151 exam by using Guaranteed Cisco CCIE Data Center Written Exam questuins and answers. Immediate access to the Up to date 400-151 Exam and find the same core area 400-151 questions with professionally verified answers, then PASS your exam with a high score now.
2026 New 400-151 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/400-151/
Q1. Which command sends a test call Home Invertor message to start the registration process
A. test callhome inventory
B. callhome inventory test
C. test inventory callhome
D. callhome test inventory
Answer: D
Q2. Which three guidelines and limitations of policy-based routing are true? (Choose three).
A. An ACL used in a policy-based routing route map cannot include a deny statement.
B. A policy-based routing route map can have multiple match or set statements per route- map statement.
C. Policy-based routing and WCCPv2 are not supported on the same interface if bank chaining is disabled.
D. The same route map can be shared among different interfaces for policy-based routing as long as the interfaces belong to the same VRF instance.
E. Setting a tunnel interface or an IP address via a tunnel interface as a next hop in a policy-based routing policy is not supported.
F. A match command can refer to more than one ACL in a route map used for policy-based routing.
Answer: A,D,E
Q3. Assuming the local peer is 10.0.0.1 and the remote peer (configuration not shown) is 10.0.0.2, which of these is used to configure PIM Anycast-RP on a Nexus 7000 switch?
A. feature pim! interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
interface loopback2 ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
ip pim anycast-rp 2.2.2.2 10.0.0.1
ip pim anycast-rp 2.2.2.2 10.0.0.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
B. feature pim
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
interface loopback2 ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
ip pim anycast-rp 10.0.0.1 2.2.2.2
ip pim anycast-rp 10.0.0.2 2.2.2.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
C. interface loopback1 ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
interface loopback2 ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
ip pim anycast-rp 2.2.2.2 10.0.0.1
ip pim anycast-rp 2.2.2.2 10.0.0.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
D. feature pim feature msdp
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0 ip pim sparse-mode
!
ip msdp originator-id loopback1
ip msdp peer 10.0.0.2 connect-source loopback1 ip msdp description 10.0.0.2 To 7010-2
ip msdp password 10.0.0.2 mypassword
!
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
Answer: A
Q4. Where is FIP negotiated?
A. between E Nodes and VF ports
B. between E Nodes and F Nodes
C. between VF ports
D. between VN ports
E. between VN ports and VF ports and FCFs
Answer: E
Q5. Which three options are valid local disk configuration policies? (Choose 3)
A. RAID 40
B. RAID 60
C. RAID 7
D. RAID 30
E. RAID 50
F. RAID 6
Answer: B,E,F
Q6. On Cisco Nexus 1000v Switch, you can allow the VSM and VEM to communicate over IP for control and packet traffic.Before you create a port profile for Layer 3 control, which two statements must be verified? (Choose two)
A. Only one port profile can be configured with the capability Layer 3 control command.
B. All VEMs belong to the same Layer 2 domain.
C. The transport mode for the VSM domain should be configured as Layer 3.
D. The port profile must be a trunk port profile.
E. Different hosts should belong to the same VLANs for Layer 3 control.
Answer: A,C
Q7. You configured a Cisco usNIC connectivity policy, for a HPC environment. Which action also must be completed?
A. Download and compile the ring_c application.
B. Install the Intel MPI library environment.
C. Mount the MPI adapter in the operating system.
D. Install an MPI environment in the operating system.
Answer: A
Q8. Refer to the exhibit.
Which network script automation option or tool is used in the exhibit?
A. REST
B. Bash script
C. NETCONF
D. Cisco EEM
E. Python
Answer: E
Q9. Refer to the exhibit.
Which two statements about this configuration command sequence with regards to the Cisco Nexus 5500 are true. (Choose two.)
A. It configures this node to use 0EFC2A as the first 3 bytes of the FPMA.
B. It configures this node to use 0EFC2A as the last 3 bytes of the FPMA.
C. It configures this node to use FCID 0EFC2A to forward the FDISC to when an endpoint is connected.
D. It reserves this FCID so only this node can use this FCID when communicating with other Fiber Channel entities.
E. It permits this node to form FCoE ISLs only with other nodes configured for the same FC-MAP
Answer: A,C
Q10. Refer to the exhibit.
Which statement about this output from two different switches is true?
A. Based on this exhibit, a zone merge problem will occur.
B. There is no way to tell if a zone merge problem will be encountered with just the current display. Additional commands will need to be performed order to determine if a problem exists.
C. Based on this exhibit, a zone merge problem will not occur, but a warning is generated that indicates that some minor differences in the zone it exist.
D. This exhibit shows no problem. No zone merge issues occur for VSAN 1 based on the current displays.
Answer: A