Cause all that matters here is passing the Cisco 644-906 exam. Cause all that you need is a high score of 644-906 Implementing and Maintaining Cisco Technologies Using IOS XR - (IMTXR) exam. The only one thing you need to do is downloading Actualtests 644-906 exam study guides now. We will not let you down with our money-back guarantee.


2026 New 644-906 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/644-906/

Q1. What are the two commands to show all log entries except BGP or configuration-related ones? (Choose two.) 

A. show log | excl [BGP,CONFIG] 

B. show log | excl BGP | excl CONFIG 

C. show log | excl (BGP,CONFIG) 

D. show log | excl "BGP|CONFIG" 

Answer: B,D 

Q2. Which two of the following are correct commands to activate the PIE file <hfr-mgbl-p.pie-4.0.1>? (Choose two.) 

A. install add tftp://172.20.165.36/hfr-mgbl-p.pie-4.0.1 activate 

B. install activate tftp://172.20.165.36/hfr-mgbl-p.pie-4.0.1 

C. install add disk0:hfr-mgbl-p-4.0.1 activate 

D. install activate disk0:hfr-mgbl-p.pie-4.0.1 

Answer: A,D 

Q3. What is the correct command to copy the contents of the harddisk:/showtech folder to an FTP server? 

A. copy harddisk:/showtech location 0/RSP0/CPU0 ftp: 

B. copy harddisk:/showtech ftp: 

C. copy /recurse harddisk:/showtech location 0/RSP0/CPU0 ftp: 

D. copy /recurse harddisk:/showtech ftp: 

E. copy ftp: harddisk:/showtech 

Answer: C 

Q4. Refer to the show environmental power-supply command output exhibit. 

How much power is the system currently using? 

A. 663 W 

B. 1150 W 

C. 1850 W 

D. 6000 W 

Answer: A 

Q5. Where are client interfaces terminated on the Cisco CRS-3? 

A. the modular services card 

B. the physical layer interface module(s) 

C. the switch fabric interface terminator 

D. the Service Processor 40 

E. the Service Processor 140 

Answer: B 

Q6. In which mode can you check the power usage of a chassis? 

A. in EXEC mode 

B. in admin mode 

C. in both EXEC and admin mode 

D. in ROMMON mode 

E. in environmental mode 

Answer: B 

Q7. Referring to the configuration output exhibit, which set of commands below will allow you to insert a new line just before the permit any statement? 

A. :router#configure :router(config)#ipv4 access-list Ethernet_In :router(config-ipv4-acl)# 2.5 deny udp any eq tftp any 

B. :router#configure :router(config)#ipv4 access-list Ethernet_In :router(config-ipv4-acl)# insert after 2 deny udp any eq tftp any 

C. :router #resequence access-list ipv4 Ethernet_In :router#configure :router(config)#ipv4 access-list Ethernet_In :router(config-ipv4-acl)#25 deny udp any eq tftp any 

D. :router#configure :router(config)#ipv4 access-list Ethernet_In :router(config-ipv4-acl)#move 3 to 4 :router(config-ipv4-acl)#3 deny udp any eq tftp any 

Answer: C 

Q8. Which command should be used to view only the running configuration of OSPF in Cisco IOS XR Software? 

A. show router ospf 

B. show run router ospf 

C. show configuration ospf 

D. show ospf configuration | running-config 

E. show ospf process 

Answer: B 

Q9. Where is the LPTS policer applied? 

A. egress line-card egress queue 

B. egress line-card CPU 

C. route processor CPU 

D. distributed RP CPU 

E. ingress line card 

Answer: E 

Q10. Refer to the exhibit. 

If you have ROMMONs and FPDs with the Upg/Dng field marked "Yes" and you ran the upgrade hw-module fpd all location all command, what did you upgrade? 

A. upgraded only the FPD for the cards that the Upg/Dng field marked "Yes" 

B. upgraded all of the FPDs on all cards with an FPD regardless of the Upg/Dng field markings C. upgraded only the FPD and ROMMON for the cards that the Upg/Dng field marked "Yes" 

D. upgraded all of the FPDs and ROMMONs on all cards with an FPD or ROMMON regardless of the Upg/Dng field markings 

Answer: C