The Secret of Juniper JN0-102 exam question

Question No: 5

Which two statements are true about terms in a routing policy? (Choose two.)

A. A routing policy cannot have more than one term.

B. If a term does not contain a from statement, all routes match.

C. If a term does not contain a from statement, the Junos OS will not commit.

D. A then statement is not mandatory in a term.

View Answer

Question No: 6

Which statement is true about the routing table?

A. The routing table exists in the control plane only.

B. The routing table exists in the control plane and in the forwarding plane.

C. The routing table contains both active and inactive routes.

D. The routing table is stored on compact flash.

View Answer

Question No: 7

What are two examples of exception traffic? (Choose two.)

A. SFTP traffic that enters one interface and is destined for a local physical interface.

B. SFTP traffic that enters and exits the same interface on the local router.

C. SCP traffic that enters one interface and exits another interface on the local router.

D. SCP traffic that is destined for the routeru2021s loopback interface.

View Answer

Question No: 8

What does the "3" in Junos version 14.2R3.2 represent?

A. A service build number

B. A single-threaded version of the Junos OS

C. A major release number

D. A minor release number

View Answer

Question No: 9

-- Exhibit --

user@router> show route protocol static

inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden)

+ = Active Route, - = Last Active, * = Both

192.168.1.0/24 *[Static/5] 00:03:13

>to 10.20.106.10 via fe-0/0/5.1 192.168.1.192/26 *[Static/5] 00:03:13

>to 10.20.14.131 via ge-0/0/0.0 192.168.1.192/27 *[Static/5] 00:03:13

>to 10.18.1.1 via ge-0/0/1.0 192.168.1.4/30 *[Static/5] 00:01:06

>to 10.20.14.130 via ge-0/0/0.0

-- Exhibit --

Using the routing table shown in the exhibit, what will be the next-hop IP address used for a destination IP address of 192.168.1.1? (Assume that the only routes to this destination are static routes.)

A. 10.20.14.130

B. 10.18.1.1

C. 10.20.14.131

D. 10.20.106.10

View Answer

Question No: 10

By default, if equal-cost paths exist for the same destination, which action will the router take?

A. Drop half the traffic.

B. Make a copy of the traffic and send it to both destinations.

C. Load-balance traffic between the available paths.

D. Randomly select one of the available paths to send traffic.

View Answer

Question No: 11

-- Exhibit -- [editsnmp] user@router# show

communityCommunityA { authorization read-only; clients {

192.168.1.0/28;

}

}

trap-groupgroupA { categories {

link;

}

targets { 192.168.100.1;

192.168.200.1;

}

}

-- Exhibit --

Referring to the exhibit, what is the purpose of the targets section of the configuration?

A. It defines which devices will be sending traps.

B. It specifies where to send traps.

C. It defines the IP addresses of management systems that can access the device.

D. It specifies which devices can be polled for SNMP data.

View Answer

Question No: 12

Which statement describes an advantage of dynamic routing?

A. Dynamic routing is typically more scalable when compared to static routing.

B. Unlike static routing, dynamic routing requires no initial user configuration.

C. Unlike static routing, dynamic routing provides redundant IP addresses for end-user devices.

D. Dynamic routing provides DNS services along with IP connectivity, whereas static routing does not.

View Answer

Question No: 13

Click the Exhibit button.

Referring to the exhibit, which next-hop interface will be used to reach the 10.21.14.16 destination?

A. ge-0/0/3.0

B. ge-0/0/0.0

C. ge-0/0/2.0

D. ge-0/0/1.0

View Answer

Question No: 14

-- Exhibit --

[edit interfaces]

user@router# show

...

lo0 { unit 0 {

familyinet { filter {

input protect-loopback;

}

address 192.168.100.1/32;

}

}

}

-- Exhibit --

Given the configuration shown in the exhibit, what is the function of the protect-loopback filter?

A. to protect the Routing Engine

B. to protect all interfaces on the device

C. to protect the Packet Forwarding Engine

D. to protect the management interface

View Answer