The Secret Of HP Hpe6-a41 Dumps

NEW QUESTION 1
Refer to the exhibit.


Switch 1 shown in the exhibit is an ArubaOS switch that has an uplink to the network core on interface 25. The network administrator wants to add a link on interface 26. The administrator creates a link aggregation with this command:
Switch1 (config)# trunk 25-26 trk1 lacp
What else must the administrator do to enable the Switch 1 link aggregation to successfully pass all traffic to the core?

• A. Configure VLANs 10 and 20 as tagged VLANs on interface 26.
• B. Configure VLANs 10 and 20 as tagged VLANs on trk1.
• C. Enable BPDU filtering on interface 26.
• D. Enable LACP in active or passive mode on interfaces 25 and 26.

Answer: A

NEW QUESTION 2
Which settings should match on physical interfaces before a network administrator combines them in a link aggregation?

• A. speed and duplex mode
• B. DSCP and media
• C. speed and VLANs
• D. LLDP TLVs and VLAns

Answer: A

NEW QUESTION 3
A network administrator needs to complete the initial setup on an ArubaOS switch with the use of remote access. How can the network administrator do this?

• A. Connect the switch’s OOBM port to the same VLAN as the management station, and then establish a Telnet session to the switch default IP address.
• B. Connect the switch’s OOBM port to the same VLAN as Aruba AirWav
• C. Then manually discover the switch in AirWave using the switch default IP address.
• D. Send a Reverse ARP from the management station and assign a temporary IP to the workstation.
• E. Set up the network DHCP server to assign the switch a reserved IP addres
• F. Connect the switch to a VLAN with DHCP services and then establish a Telnet session to the reserved IP address.

Answer: B

NEW QUESTION 4
Refer to the exhibit.

The link between Core-1 and Core-2 shown in the exhibit fails, and some users lose connectivity. What should the network administrator do to prevent this issue in a situation such as this?

• A. Configure BPDU protection on all Core-2 ports.
• B. Enable IP routing on Core-2.
• C. Create routes to 10.1.10.0/24 and 10.1.11.0/24 through 10.1.1.3 on Core-2.
• D. Extend VLANs 10 and 11 on all switch-to-switch links.

Answer: D

NEW QUESTION 5
A network administrator needs to configure a static route. What should the administrator use as the next hop address?

• A. the lowest IP address on the neighboring router in the path towards its destination
• B. the IP address on the local interface that is used to egress traffic towards its destination
• C. the IP address of the default gateway in the destination subnet
• D. the IP address on the connected interface of a neighboring router in the path towards its destination

Answer: D

NEW QUESTION 6
Refer to the exhibit.

Based on the topology shown in the exhibit, which symptom does a network administrator see if the ArubaOS switches are in their factory default states?

• A. Ports places in a blocking state
• B. Mislearned MAC addresses
• C. TTL expired in transit
• D. Layer 3 loop

Answer: D

NEW QUESTION 7
An ArubaOS switch operates at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection carries untagged traffic. The administrator wants to use Telnet log in to the switch CLI.
How should the administrator contact the switch and log in?

• A. Contact the switch at its default IP address 172.16.0.254/24 and log in without entering a password.
• B. Contact the switch at its default IP address 192.168.1.1/24 and log in with the default password admin.
• C. Contact the switch at its DHCP-assigned IP address and log in without entering a password.
• D. Contact the switch at its DHCP-assigned IP address and log in with the default password aruba.

Answer: B

NEW QUESTION 8
A network administrator enters this command on an ArubaOS switch with IP routing enabled:

This is the only IP route to 0.0.0.0/0 on the switch. What is the effect?

• A. The switch uses this route to route all traffic from 10.1.1.1.
• B. The switch uses this route for all traffic unless the traffic matches a route with a lower cost than 10.
• C. The switch uses this route for all traffic unless the traffic matches a route with a lower administrative distance than 10.
• D. The switch uses this route for all traffic that does not match a specific route in its routing table.

Answer: D

NEW QUESTION 9
What is a valid setup for a Virtual Switching Framework (VSF) fabric?

• A. one 5406R zl2 switch as commander and one 5412R zl2 switch as a standby member
• B. one 5412R zl2 switch as commander and two 5406R zl2 switches as standby members
• C. one 5406R zl2 switch as commander and two 5412R zl2 switches as standby members
• D. one 5412R zl2 switch as commander and one 5412R zl2 switch as a standby member

Answer: D

NEW QUESTION 10
A retail company needs a quick way to deploy network infrastructure to new sites.
Which Aruba solutions provide Zero Touch Provisioning (ZTP) for Aruba Instant APs (IAPs) and ArubaOS switches?

• A. Aruba AirWave and Aruba Activate
• B. Aruba Meridian and Aruba ALE
• C. Aruba AirWave and Aruba Central
• D. Aruba Activate and Aruba Meridian

Answer: A

NEW QUESTION 11
A network administrator wants to deploy Aruba Instant APs (IAPs) at a remote site that does not have Internet access. The APs should receive their configuration automatically from AirWave by using Zero Touch Provisioning (ZTP). What does the administrator need to configure?

• A. the name and password of a user with full administrative rights to AirWave
• B. the name of the AirWave VLAN with the configuration that the APs should use
• C. the DHCP server configured with options 43 and 60 for ZTP
• D. the IP address for the DNS server with the mapping for the airwave hostname

Answer: C

NEW QUESTION 12
A network administrator is in the context in an ArubaOS switch CLI: Switch (vlan10)#
The administrator wants to leave the configuration context with a single command. Which command should the administrator enter?

• A. logout
• B. quit
• C. exit
• D. end

Answer: B

NEW QUESTION 13
For which task does a network administrator need to access the enable context on an ArubaOS switch?

• A. to view interface statistics
• B. to view CPU statistics
• C. to ping an IP address
• D. to view configuration files

Answer: D

NEW QUESTION 14
Refer to the exhibit.

MSTP is implemented in the topology shown in the exhibit, and all the switches are in the same region. The network administrator does not want to use the Internal Spanning Tree (IST) or instance 0 for production traffic.
How many non-IST spanning tree instances does this network need in order to have effective load sharing on the uplinks from the access switches?

• A. two
• B. three
• C. four
• D. five

Answer: C

NEW QUESTION 15
What is one advantage of OSPF over static routing?

• A. OSPF allows ArubaOS switches to use default routes, while static routes cannot use 0.0.0.0/0 as the destination network.
• B. OSPF has a lower default administrative distance than static routing on ArubaOS switches.
• C. OSPF better meets the needs of a complex topology with many redundant routes that static routing.
• D. OSPF permits load sharing traffic over multiple routes, while static routing does not.

Answer: C

NEW QUESTION 16
A company needs a switch that supports 10GbE and 40GbE for its mid-sized campus. The company prefers stackable, or fixed port, switches over modular switches. Which ArubaOS switch series best meet these needs?

• A. Aruba 2530
• B. Aruba 2930F
• C. Aruba 3810
• D. Aruba 5400R

Answer: B

NEW QUESTION 17
Refer to the exhibit. Exhibit 1.

Exhibit 2.

The routing configuration must support this behavior:
What must the network administrator change to meet these criteria?

• A. On Switch 3, add a route to 192.168.2.0/24 through 192.168.1.9 and a route to 192.168.3.0/24 through 192.168.1.5.
• B. On Switch-1, Switch-2, and Switch-3, change the next hop in each static route to specify an IP address that exists on that switch.
• C. On Switch-1, raise the administrative distance for the second route to 192.168.3.0/24; on Switch-2, raise the administrative distance for the second route to 192.168.2.0/24
• D. On Switch-1, add a route to 192.168.1.8/30 through 192.168.0.3; on Switch-2, add a route to 192.168.1.4/30 through 192.168.1.1; on Switch-3, add a route to 192.168.1.0/30 through 192.169.1.4.
• E. On Switch-1, add a route to 192.168.1.8/30 through 192.168.1.2; on Switch-2, add a route to 192.168.1.4/30 through 192.168.1.1; on Switch-3, add a route to 192.168.1.0/30 through 192.168.1.4.

Answer: C

NEW QUESTION 18
Refer to the exhibit.

Based on the output shown in this exhibit, which statement is true about the 10.0.0.2 neighbor?

• A. The neighbor rejects communications because it already has its maximum number of neighbors.
• B. The neighbor has mismatched settings and cannot exchange information with this switch.
• C. The neighbor communicates with this switch, but it cannot hold any more routes in its database.
• D. The neighbor communicates with this switch, and they have exchanged all topology information.

Answer: D

NEW QUESTION 19
Refer to the exhibit.


A network administrator executes this command on an ArubaOS switch, Switch-2: Switch-2(config)# ip route 10.1.100.0/24 10.1.1.1
The administrator successfully pings Device 1 at 10.1.100.42 from Switch-2. However, Device 2 cannot ping Device 1.
The administrator confirms that Device 1 is correctly set up.
What should the administrator check on Switch-2 to resolve this issue?

• A. that ARP proxy is enabled
• B. that IP routing is enabled
• C. that spanning tree is disabled
• D. that ICMP is enabled

Answer: B

NEW QUESTION 20
Refer to the exhibit.
Exhibit 1.

Exhibit 2.

Assume that Switch-2 is correctly configured for OSPF.
Which additional step must the administrator take to enable Switch-1 to advertise 192.168.2.0/24 to Switch-2?

• A. Set a router ID on Switch-1.
• B. Configure a route to advertise 192.168.2.0/24 on Switch-1.
• C. Add Switch-2’s router ID to Switch-1’s OSPF neighbor list.
• D. Enable OSPF on VLAN 2.

Answer: D

NEW QUESTION 21
A Virtual Switching Framework (VSF) fabric is configured to use LLDP-MAD.
Which action does the standby member take if it sends a probe but receives no response?

• A. It sends a request packet to the commander to determine which ports should remain active.
• B. It continues to function and assumes the role of commander.
• C. It automatically changes its status to MAD inactive fragment.
• D. It requests that the commander change its status to MAD inactive fragment.

Answer: A

NEW QUESTION 22
Why would a network administrator use strict provisioning to configure the standby member in a Virtual Switching Framework (VSF) fabric?

• A. The network administrator wants to control which device can join the VSF fabric.
• B. The network administrator needs to configure the correct domain ID on the standby member before this member joins the VSF fabric.
• C. The network administrator wants to ensure the standby member is configured with the same settings as the commander.
• D. The network administrator does not know the MAC address of the standby member.

Answer: A

NEW QUESTION 23
......