It is more faster and easier to pass the Cisco 100 105 icnd1 pdf exam by using Vivid Cisco Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) questuins and answers. Immediate access to the Updated ccna 100 105 pdf Exam and find the same core area 100 105 icnd1 pdf questions with professionally verified answers, then PASS your exam with a high score now.
2026 New 100-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/100-105/
Q1. - (Topic 7)
Which value is indicated by the next hop in a routing table?
A. preference of the route source
B. IP address of the remote router for forwarding the packets
C. how the route was learned
D. exit interface IP address for forwarding the packets
Answer: D
Explanation:
The routing table contains network/next hop associations. These associations tell a router that a particular destination can be optimally reached by sending the packet to a specific router that represents the "next hop" on the way to the final destination. The next hop association can also be the outgoing or exit interface to the final destination.
Q2. - (Topic 3)
Refer to the exhibit.
Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Answer: B,C
Explanation:
A loopback interface never comes down even if the link is broken so it provides stability for the OSPF process (for example we use that loopback interface as the router-id) -The router-ID is chosen in the order below:
+
The highest IP address assigned to a loopback (logical) interface.
+
If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen. -> The loopback interface will be chosen as the router ID of RouterB -
Q3. - (Topic 7)
Which statement about routing protocols is true?
A. Link-state routing protocols choose a path by the number of hops to the destination.
B. OSPF is a link-state routing protocol.
C. Distance-vector routing protocols use the Shortest Path First algorithm.
D. IS-IS is a distance-vector routing protocol.
Answer: A
Explanation: Link State Routing Protocols
Link state protocols are also called shortest-path-first protocols. Link state routing protocols have a complete picture of the network topology. Hence they know more about the whole network than any distance vector protocol. Three separate tables are created on each link state routing enabled router. One table is used to hold details about directly connected neighbors, one is used to hold the topology of the entire internetwork and the last one is used to hold the actual routing table. Link state protocols send information about directly connected links to all the routers in the network. Examples of Link state routing protocols include OSPF - Open Shortest Path First and IS-IS - Intermediate System to Intermediate System. There are also routing protocols that are considered to be hybrid in the sense that they use aspects of both distance vector and link state protocols. EIGRP - Enhanced Interior Gateway Routing Protocol is one of those hybrid routing protocols.
Q4. - (Topic 5)
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the
configuration.
E. It will encrypt all current and future passwords.
Answer: E
Explanation:
Encryption further adds a level of security to the system as anyone having access to the database of passwords cannot reverse the process of encryption to know the actual passwords which isn’t the case if the passwords are stored simply.
Q5. - (Topic 7)
Which statement about the inside interface configuration in a NAT deployment is true?
A. It is defined globally
B. It identifies the location of source addresses for outgoing packets to be translated using access or route maps.
C. It must be configured if static NAT is used
D. It identifies the public IP address that traffic will use to reach the internet.
Answer: B
Explanation:
This module describes how to configure Network Address Translation (NAT) for IP address conservation and how to configure inside and outside source addresses. This module also provides information about the benefits of configuring NAT for IP address conservation. NAT enables private IP internetworks that use nonregistered IP addresses to connect to the Internet. NAT operates on a device, usually connecting two networks, and translates the private (not globally unique) addresses in the internal network into legal addresses before packets are forwarded onto another network. NAT can be configured to advertise to the outside world only one address for the entire network. This ability provides additional security by effectively hiding the entire internal network behind that one address. NAT is also used at the enterprise edge to allow internal users access to the Internet and to allow Internet access to internal devices such as mail servers.
Q6. - (Topic 3)
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.
The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
Answer: D
Explanation:
In OSPF, the hello and dead intervals must match and here we can see the hello interval is set to 5 on R1 and 10 on R2. The dead interval is also set to 20 on R1 but it is 40 on R2.
Q7. - (Topic 7)
Which statement about a router on a stick is true?
A. Its date plane router traffic for a single VI AN over two or more switches.
B. It uses multiple subinterfaces of a single interface to encapsulate traffic for different VLANs on the same subnet.
C. It requires the native VLAN to be disabled.
D. It uses multiple subinterfaces of a single interface to encapsulate traffic for different VLANs.
Answer: D
Explanation:
https://www.freeccnaworkbook.com/workbooks/ccna/configuring-inter-vlan-routing-router-on-a-stick
Q8. - (Topic 3)
ROUTER# show ip route
192.168.12.0/24 is variably subnetted, 9 subnets, 3 masks C 192.168.12.64 /28 is directly connected, Loopback1 C 192.168.12.32 /28 is directly connected, Ethernet0 C 192.168.12.48 /28 is directly connected, Loopback0 O 192.168.12.236 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 C 192.168.12.232 /30 is directly connected, Serial0 O 192.168.12.245 /30 [110/782] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.240 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.253 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O 192.168.12.249 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O 192.168.12.240/30 [110/128] via 192.168.12.233, 00:35:36, Serial 0
To what does the 128 refer to in the router output above?
A. OSPF cost
B. OSPF priority
C. OSPF hop count
D. OSPF ID number
E. OSPF administrative distance
Answer: A
Explanation:
The first parameter is the Administrative Distance of OSPF (110) while the second parameter is the cost of OSPF.
Q9. - (Topic 7)
By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled?
A. 8
B. 2
C. 1
D. 0
Answer: C
Q10. - (Topic 5)
Refer to the exhibit.
A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume.
Answer: D
Explanation:
Because Switch1 has multiple redundant links in this network, traffic would not work for less than a minute, and then it would get rerouted along the longer path to the host. The 1 minute outage would be the length of time it takes STP to converge.