We provide real ccent ccna icnd1 100 105 official cert guide exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco 100 105 icnd1 Exam quickly & easily. The ccna 100 105 pdf PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco ccent 100 105 dumps pdf and vce product and material, you can easily pass the 100 105 icnd1 exam.
2026 New 100-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/100-105/
P.S. Download 100-105 braindump are available on Google Drive, GET MORE: https://drive.google.com/open?id=1wKeQp_fzylh6B_iOxIFNYB8egVM39bjO
New Cisco 100-105 Exam Dumps Collection (Question 2 - Question 11)
Q1. Refer to the exhibit.
After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch?
A. The POST was successful.
B. The switch has a problem with the internal power supply and needs an external power supply to be attached.
C. POST failed and there is a problem that prevents the operating system from being loaded.
D. The switch has experienced an internal problem but data can still be forwarded at a slower rate.
E. The switch passed POST, but all the switch ports are busy.
Answer: C
Explanation:
http://www.cisco.com/en/US/products/hw/switches/ps607/products_tech_note09186a00801 25913.shtml
Each time you power up the switch, eight Power-On Self Tests (POSTs) run automatically. POSTs check the most important system components before the switch begins to forward packets. When the switch begins the POST, the port status LEDs display amber for two seconds, and then display green. As each test runs, the port status LEDs go out. 1x is the first to go out. The port status LEDs for ports 2x through 8x go out sequentially as the system completes a test.
When the POST completes successfully, the port status LEDs go out. This indicates that the switch is operational. If a test fails, the port status LED associated with the test displays
amber. The system LED also displays amber.
Not E: From Cisco IOS Software Release 11.2(8.5) SA6 onwards, the port and system LEDs both remain amber after a POST failure. In the earlier Cisco IOS Software Releases, only the LEDs of failed linked ports remained amber.
Q2. Refer to the exhibit.
An administrator replaced the 10/100 Mb NIC in a desktop PC with a 1 Gb NIC and now the PC will not connect to the network. The administrator began troubleshooting on the switch. Using the switch output shown, what is the cause of the problem?
A. Speed is set to 100Mb/s.
B. Input flow control is off.
C. Encapsulation is set to ARPA.
D. The port is administratively down.
E. The counters have never been cleared.
Answer: A
Explanation:
For PC to switch connectivity, the speed settings must match. In this case, the 1 Gb NIC will not be able to communicate with a 100Mb fast Ethernet interface, unless the 1Gb NIC can be configured to connect at 100Mb.
Q3. If an Ethernet port on a router was assigned an IP address of 172.16.112.1/20, what is the maximum number of hosts allowed on this subnet?
A. 1024
B. 2046
C. 4094
D. 4096
E. 8190
Answer: C
Explanation:
Each octet represents eight bits. The bits, in turn, represent (from left to right): 128, 64, 32 , 16 , 8, 4, 2, 1
Add them up and you get 255. Add one for the all zeros option, and the total is 256. Now, take away one of these for the network address (all zeros) and another for the broadcast address (all ones). Each octet represents 254 possible hosts. Or 254 possible
networks. Unless you have subnet zero set on your network gear, in which case you could conceivably have 255.
The CIDR addressing format (/20) tells us that 20 bits are used for the network portion, so the maximum number of networks are 2^20 minus one if you have subnet zero enabled, or minus 2 if not.
You asked about the number of hosts. That will be 32 minus the number of network bits, minus two. So calculate it as (2^(32-20))-2, or (2^12)-2 = 4094
Q4. What is the subnet address for the IP address 172.19.20.23/28?
A. 172.19.20.0
B. 172.19.20.15
C. 172.19.20.16
D. 172.19.20.20
E. 172.19.20.32
Answer: C
Explanation:
From the /28 we can get the following:
Increment: 16 (/28 = 11111111.11111111.11111111.11110000)
Network address: 172.19.20.16 (because 16 < 23)
Broadcast address: 172.16.20.31 (because 31 = 16 + 16 u2013 1)
Q5. Refer to the exhibit.
An administrator cannot connect from R1 to R2. To troubleshoot this problem, the administrator has entered the command shown in the exhibit. Based on the output shown, what could be the problem?
A. The serial interface is configured for half duplex.
B. The serial interface does not have a cable attached.
C. The serial interface has the wrong type of cable attached.
D. The serial interface is configured for the wrong frame size.
E. The serial interface has a full buffer.
Answer: C
Explanation:
http://www.thebryantadvantage.com/CCNACertificationExamTutorialDirectlyConnectedSerialInterfaces.htm
Since the output is not forthcoming it shows that the type of cable attached is wrong, though the cable is connected since it shows the cable type.
According to the figure DTE cable should connect to R1 on interface but while examining using show controllers serial 0/0 command it showing that a DCE is connected so the wrong type of cable is being used.
Q6. An administrator is working with the 192.168.4.0 network, which has been subnetted with a /26 mask. Which two addresses can be assigned to hosts within the same subnet? (Choose two.)
A. 192.168.4.61
B. 192.168.4.63
C. 192.168.4.67
D. 192.168.4.125
E. 192.168.4.128
F. 192.168.4.132
Answer: C,D
Explanation:
Increment: 64 (/26 = 11111111.11111111.11111111.11000000)
The IP 192.168.4.0 belongs to class C. The default subnet mask of class C is /24 and it has been subnetted with a /26 mask so we have 2(26-24) = 22 = 4 sub-networks:
1st subnet: 192.168.4.0 (to 192.168.4.63)
2nd subnet: 192.168.4.64 (to 192.168.4.127)
3rd subnet: 192.168.4.128 (to 192.168.4.191)
4th subnet: 192.168.4.192 (to 192.168.4.225)
In all the answers above, only answer C and D are in the same subnet. Therefore only IPs in this range can be assigned to hosts.
Q7. Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.)
A. layer 3 support
B. port security
C. redundant components
D. VLANs
E. PoE
Answer: B,D
Explanation: Access layer
The main purpose of the access layer is to provide direct connection to devices on the network and controlling which devices are allowed to communicate over it. The access layer interfaces with end devices, such as PCs, printers, and IP phones, to provide access to the rest of the network. The access layer can include routers, switches, bridges, hubs, and wireless access points (AP).
Switch features in the Access layer:
u2711 Port security
u2711 VLANs
u2711 Fast Ethernet/Gigabit Ethernet
u2711 Power over Ethernet (PoE)
u2711 Link aggregation
u2711 Quality of Service (QoS)
References: http://www.ciscopath.com/content/61/ http://www.mcmcse.com/cisco/guides/hierarchical_model.shtml
Q8. Which statement describes the process ID that is used to run OSPF on a router?
A. It is globally significant and is used to represent the AS number.
B. It is locally significant and is used to identify an instance of the OSPF database.
C. It is globally significant and is used to identify OSPF stub areas.
D. It is locally significant and must be the same throughout an area.
Answer: B
Explanation:
The Process ID for OSPF on a router is only locally significant and you can use the same number on each router, or each router can have a different number-it just doesn't matter. The numbers you can use are from 1 to 65,535. Don't get this confused with area numbers, which can be from 0 to 4.2 billion.
Q9. Refer to the topology and switching table shown in the graphic.
Host B sends a frame to Host C. What will the switch do with the frame?
A. Drop the frame
B. Send the frame out all ports except port 0/2
C. Return the frame to Host B
D. Send an ARP request for Host C
E. Send an ICMP Host Unreachable message to Host B
F. Record the destination MAC address in the switching table and send the frame directly to Host C
Answer: B
Q10. A network administrator is connecting PC hosts A and B directly through their Ethernet interfaces as shown in the graphic. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts? (Choose two.)
A. A crossover cable should be used in place of the straight-through cable.
B. A rollover cable should be used in place of the straight-through cable.
C. The subnet masks should be set to 255.255.255.192
D. A default gateway needs to be set on each host.
E. The hosts must be reconfigured to use private IP addresses for direct connections of this type.
F. The subnet masks should be set to 255.255.255.0
Answer: A,F
Explanation:
If you need to connect two computers but you don't have access to a network and can't set up an ad hoc network, you can use an Ethernet crossover cable to create a direct cable connection.
Generally speaking, a crossover cable is constructed by reversing (or crossing over) the order of the wires inside so that it can connect two computers directly. A crossover cable looks almost exactly like a regular Ethernet cable (a straight-through cable), so make sure you have a crossover cable before following these steps.
Both devices need to be on the same subnet, and since one PC is using 192.1.1.20 and the other is using 192.1.1.201, the subnet mask should be changed to 255.255.255.0.
P.S. Easily pass 100-105 Exam with Certleader Download Dumps & pdf vce, Try Free: https://www.certleader.com/100-105-dumps.html (347 New Questions)