We provide real cisco ccna 200 125 exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco ccna 200 125 dumps Exam quickly & easily. The ccna routing and switching 200 125 official cert guide library PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco ccna 200 125 pdf dumps pdf and vce product and material, you can easily pass the ccna 200 125 pdf exam.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. - (Topic 8)
On which type of device is every port in the same collision domain?
A. a router
B. a Layer 2 switch
C. a hub
Answer: C
Explanation: Collision domainA collision domain is, as the name implies, a part of a
network where packet collisions can occur. A collision occurs when two devices send a packet at the same time on the shared network segment. The packets collide and both devices must send the packets again, which reduces network efficiency. Collisions are often in a hub environment, because each port on a hub is in the same collision domain. By contrast, each port on a bridge, a switch or a router is in a separate collision domain.
Q2. - (Topic 7)
Scenario:
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the issue?
A. R1 ethernet0/1 is shutdown. Configure no shutdown command.
B. R1 ethernet0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25.
C. R2 ethernet0/1 and R3 ethernet0/0 are configured with a non-default OSPF hello
interval of 25; configure no ip ospf hello-interval 25.
D. Enable OSPF for R1 ethernet0/1; configure ip ospf 1 area 0 command under ethernet0/1.
Answer: B
Explanation:
Looking at the configuration of R1, we see that R1 is configured with a hello interval of 25 on interface Ethernet 0/1 while R2 is left with the default of 10 (not configured).
Q3. - (Topic 8)
While troubleshooting a connection problem on a computer, you determined that the computer can ping a specific web server but it cannot connect to TCP port 80 on that server. Which reason for the problem is most likely true?
A. A VLAN number is incorrect.
B. A Route is missing
C. An ARP table entry is missing.
D. An ACL is blocking the TCP port.
Answer: D
Q4. - (Topic 8)
What is the best way to verify that a host has a path to other hosts in different networks?
A. Ping the loopback address.
B. Ping the default gateway.
C. Ping the local interface address.
D. Ping the remote network.
Answer: D
Explanation:
Ping is a tool that helps to verify IP-level connectivity; PathPing is a tool that detects packet loss over multiple-hop trips. When troubleshooting, the ping command is used to send an ICMP Echo Request to a target host name or IP address. Use Ping whenever you want to verify that a host computer can send IP packets to a destination host. You can also use the Ping tool to isolate network hardware problems and incompatible configurations.
If you call ipconfig /all and receive a response, there is no need to ping the loopback address and your own IP address — Ipconfig has already done so in order to generate the report.
It is best to verify that a route exists between the local computer and a network host by first using ping and the IP address of the network host to which you want to connect. The command syntax is:
ping < IP address >
Perform the following steps when using Ping:
✑ Ping the loopback address to verify that TCP/IP is installed and configured correctly on the local computer.
ping 127.0.0.1
If the loopback step fails, the IP stack is not responding. This might be because the TCP drivers are corrupted, the network adapter might not be working, or another service is interfering with IP.
✑ Ping the IP address of the local computer to verify that it was added to the network
correctly. Note that if the routing table is correct, this simply forwards the packet to the loopback address of 127.0.0.1.
ping < IP address of local host >
✑ Ping the IP address of the default gateway to verify that the default gateway is functioning and that you can communicate with a local host on the local network.
ping < IP address of default gateway >
✑ Ping the IP address of a remote host to verify that you can communicate through a router.
ping < IP address of remote host >
✑ Ping the host name of a remote host to verify that you can resolve a remote host name.
ping < Host name of remote host >
✑ Run a PathPing analysis to a remote host to verify that the routers on the way to the destination are operating correctly.
pathping < IP address of remote host >
Q5. - (Topic 7)
Scenario:
Refer to the topology. Your company has decided to connect the main office with three
other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R4 in the Branch1 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a Layer 2 issue; an encapsulation mismatch on serial links.
C. There is an OSPF hello and dead interval mismatch.
D. The R3 router ID is configured on R4.
Answer: A
Explanation:
A show running-config command on R3 and R4 shows that R4 is incorrectly configured for area 2:
Q6. - (Topic 5)
How is an EUI-64 format interface ID created from a 48-bit MAC address?
A. by appending 0xFF to the MAC address
B. by prefixing the MAC address with 0xFFEE
C. by prefixing the MAC address with 0xFF and appending 0xFF to it
D. by inserting 0xFFFE between the upper three bytes and the lower three bytes of the MAC address
E. by prefixing the MAC address with 0xF and inserting 0xF after each of its first three bytes
Answer: D
Explanation:
The modified EUI-64 format interface identifier is derived from the 48-bit link-layer (MAC) address by inserting the hexadecimal number FFFE between the upper three bytes (OUI field) and the lower three bytes (serial number) of the link layer address.
Q7. - (Topic 4)
Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?
A. Router(config-if)# ppp authentication chap fallback ppp
B. Router(config-if)# ppp authentication chap pap
C. Router(config-if)# authentication ppp chap fallback ppp
D. Router(config-if)# authentication ppp chap pap
Answer: B
Explanation:
This command tells the router first to use CHAP and then go to PAP if CHAP isn't available.
Q8. - (Topic 6)
How does using the service password-encryption command on a router provide additional security?
A. by encrypting all passwords passing through the router
B. by encrypting passwords in the plain text configuration file
C. by requiring entry of encrypted passwords for access to the device
D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges
E. by automatically suggesting encrypted passwords for use in configuring the router
Answer: B
Explanation:
By using this command, all the (current and future) passwords are encrypted. This command is primarily useful for keeping unauthorized individuals from viewing your password in your configuration file
Q9. - (Topic 6)
Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?
A. BackboneFast
B. UplinkFast
C. Root Guard
D. BPDU Guard
E. BPDU Filter
Answer: D
Explanation:
We only enable PortFast feature on access ports (ports connected to end stations). But if someone does not know he can accidentally plug that port to another switch and a loop may occur when BPDUs are being transmitted and received on these ports.
With BPDU Guard, when a PortFast receives a BPDU, it will be shut down to prevent a loop.
Q10. - (Topic 8)
In which three ways is an IPv6 header simpler than an IPv4 header? (Choose three.)
A. Unlike IPv4 headers, IPv6 headers have a fixed length.
B. IPv6 uses an extension header instead of the IPv4 Fragmentation field.
C. IPv6 headers eliminate the IPv4 Checksum field.
D. IPv6 headers use the Fragment Offset field in place of the IPv4 Fragmentation field.
E. IPv6 headers use a smaller Option field size than IPv4 headers.
F. IPv6 headers use a 4-bit TTL field, and IPv4 headers use an 8-bit TTL field.
Answer: A,B,C