All About Validated 200-125 dumps

Q5. Scenario:

You work for a company that provides managed network services, and of your real estate clients running a small office is experiencing network issues, Troubleshoot the network issues.

Router R1 connects the main office to internet, and routers R2 and R3 are internal routers NAT is enabled on Router R1.

The routing protocol that is enable between routers R1, R2, and R3 is RIPv2.

R1 sends default route into RIPv2 for internal routers to forward internet traffic to R1. Server1 and Server2 are placed in VLAN 100 and 200 respectively, and dare still running

router on stick configuration with router R2.

You have console access on R1, R2, R3, and L2SW1 devices. Use only show commands to troubleshoot the issues.

What is the correct statement below after examining the R1 routing table?

A. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses static route instead RIPv2 Because the static route AD that is configured is less than the AD of RIPv2

B. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses RIPv2 instead static

route Because the static route AD that is configured is higher than the AD of RIPv2

C. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses static route instead RIPv2 But the traffic is forwarded to the ISP instead of the internal network.

D. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses RIPv2 instead static route Because the static route AD that is configured is 255

Q6. Which NAT term is defined as a group of addresses available for NAT use?

A. NAT pool

B. dynamic NAT

C. static NAT

D. one-way NAT

Q7. How does a Cisco switch respond if you boot it without a valid configuration in the NVRAM?

A. it enters setup mode.

B. it uses the running u2013configuration

C. It prompts you to restore the startup configuration

D. it enters user EXEC mode.

Q8. To enable router on a stick on a router subinterface, which two steps must you perform ? choose two

A. configure full duplex and speed

B. configure a default to route traffic between subinterfaces

C. configure the subinterface with an ip address

D. configure encapsulation dot1q

E. configure an ip route to the vlan destination network

Q9. Which option describes the best way to troubleshoot and isolate a network problem?

A. Gather the facts

B. Change one variable at a time.

C. Implement an action plan

D. Create an Action plan

Q10. Which keyword enables an HSRP router to take the active role immediately when it comes online?

A. IP address

B. Priority

C. Preempt

D. Version

Q11. Which two options describe benefits of aggregated chassis technology ( choose 2) ?

A. it reduces management overhead.

B. switches can be located anywhere regardless of their physical distance from one another.

C. it requires only one IP address per VLAN.

D. it requires only Three IP address per VLAN.

E. it supports HSRP VRRP and GLBP.

F. it support redundant configuration files.

Q12. Which function allows EIGRP peers to receive notice of implementing topology changes?

A. successors

B. advertised changes

C. goodbye messages

D. expiration of the hold timer

Q13. Which utility can you use to identify redundant or shadow rules ?

A. The ACL trace tool in Cisco APIC-EM.

B. The ACL analysis tool in Cisco APIC-EM.

C. The Cisco APIC-EM automation scheduler.

D. The Cisco IWAN application.

Q14. When troubleshooting ethernet connectivity issues how can you verify that an ip address is known to a router?

A. Check Whether the ip address is in the routing table

B. Check Whether an ACL is blocking the ip address

C. Check Whether the ip address is in the CAM Table

D. Check Whether the ip address is in the ARP Table