Pass4sure ccna 200 125 Questions are updated and all ccna 200 125 dumps answers are verified by experts. Once you have completely prepared with our ccna 200 125 book exam prep kits you will be ready for the real 200 125 cisco exam without a problem. We have Regenerate Cisco ccna 200 125 ebook dumps study guide. PASSED cisco 200 125 First attempt! Here What I Did.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. - (Topic 5)
The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)
A. no broadcast
B. change of source address in the IPv6 header
C. change of destination address in the IPv6 header
D. Telnet access does not require a password
E. autoconfiguration
F. NAT
Answer: A,E
Explanation:
IPv6 does not use broadcasts, and autoconfiguration is a feature of IPV6 that allows for hosts to automatically obtain an IPv6 address.
Q2. - (Topic 5)
Which command can you use to manually assign a static IPv6 address to a router interface?
A. ipv6 autoconfig 2001:db8:2222:7272::72/64
B. ipv6 address 2001:db8:2222:7272::72/64
C. ipv6 address PREFIX_1 ::1/64
D. ipv6 autoconfig
Answer: B
Explanation:
To assign an IPv6 address to an interface, use the “ipv6 address” command and specify the IP address you wish to use.
Q3. - (Topic 8)
Which protocol is the Cisco proprietary implementation of FHRP?
A. HSRP
B. VRRP
C. GLBP
D. CARP
Answer: A
Q4. - (Topic 7)
Which protocol can cause overload on a CPU of a managed device?
A. Netflow
B. WCCP
C. IP SLA
D. SNMP
Answer: D
Explanation:
Sometimes, messages like this might appear in the router console:
%SNMP-3-CPUHOG: Processing [chars] of [chars]
They mean that the SNMP agent on the device has taken too much time to process a request.
You can determine the cause of high CPU use in a router by using the output of the show process cpu command.
Note: A managed device is a part of the network that requires some form of monitoring and
management (routers, switches, servers, workstations, printers…).
Q5. - (Topic 7)
An administrator is trying to ping and telnet from SwitchC to RouterC with the results shown below.
Click the console connected to RouterC and issue the appropriate commands to answer the questions.
Which will fix the issue and allow ONLY ping to work while keeping telnet disabled?
A. Correctly assign an IP address to interface fa0/1.
B. Change the ip access-group command on fa0/0 from “in” to “out”.
C. Remove access-group 106 in from interface fa0/0 and add access-group 115 in.
D. Remove access-group 102 out from interface s0/0/0 and add access-group 114 in
E. Remove access-group 106 in from interface fa0/0 and add access-group 104 in.
Answer: E
Explanation:
Let’s have a look at the access list 104:
The question does not ask about ftp traffic so we don’t care about the two first lines. The 3rd line denies all telnet traffic and the 4th line allows icmp traffic to be sent (ping). Remember that the access list 104 is applied on the inbound direction so the 5th line “access-list 104 deny icmp any any echo-reply” will not affect our icmp traffic because the “echo-reply” message will be sent over the outbound direction.
Q6. - (Topic 8)
In which three ways is an IPv6 header simpler than an IPv4 header? (Choose three.)
A. Unlike IPv4 headers, IPv6 headers have a fixed length.
B. IPv6 uses an extension header instead of the IPv4 Fragmentation field.
C. IPv6 headers eliminate the IPv4 Checksum field.
D. IPv6 headers use the Fragment Offset field in place of the IPv4 Fragmentation field.
E. IPv6 headers use a smaller Option field size than IPv4 headers.
F. IPv6 headers use a 4-bit TTL field, and IPv4 headers use an 8-bit TTL field.
Answer: A,B,C
Q7. - (Topic 7)
Refer to the exhibit.
An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?
A. data link layer
B. application layer
C. access layer
D. session layer
E. network layer
Answer: E
Explanation:
The command ping uses ICMP protocol, which is a network layer protocol used to propagate control message between host and router. The command ping is often used to verify the network connectivity, so it works at the network layer.
Q8. - (Topic 8)
A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?
A. the EIGRP route
B. the OSPF route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Answer: A
Q9. - (Topic 3)
A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task?
A. service password-encryption
access-list 1 permit 192.168.1.0 0.0.0.255
line vty 0 4 login
password cisco access-class 1
B. enable password secret line vty 0
login
password cisco
C. service password-encryption line vty 1
login
password cisco
D. service password-encryption line vty 0 4
login
password cisco
Answer: C
Explanation:
Only one VTY connection is allowed which is exactly what's requested. Incorrect Answer: command.
line vty0 4
would enable all 5 vty connections.
Topic 4, WAN Technologies
Q10. - (Topic 3)
A router receives information about network 192.168.10.0/24 from multiple sources. What will the router consider the most reliable information about the path to that network?
A. a directly connected interface with an address of 192.168.10.254/24
B. a static route to network 192.168.10.0/24
C. a RIP update for network 192.168.10.0/24
D. an OSPF update for network 192.168.0.0/16
E. a default route with a next hop address of 192.168.10.1
F. a static route to network 192.168.10.0/24 with a local serial interface configured as the next hop
Answer: A
Explanation:
When there is more than one way to reach a destination, it will choose the best one based on a couple of things. First, it will choose the route that has the longest match; meaning the most specific route. So, in this case the /24 routes will be chosen over the /16 routes. Next, from all the /24 routes it will choose the one with the lowest administrative distance. Directly connected routes have an AD of 1 so this will be the route chosen.