Proper study guides for Most recent Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) certified begins with Cisco 200 125 ccna book preparation products which designed to deliver the Vivid ccna 200 125 torrent questions by making you pass the ccna 200 125 ebook test at your first time. Try the free ccna 200 125 book demo right now.
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
Q1. - (Topic 8)
Which configuration can you apply to enable encapsulation on a subinterface?
A. interface FastEthernet 0/0 encapsulation dot1Q 30
ip address 10.1.1.30 255.255.255.0
B. interface FastEthernet 0/0.30
ip address 10.1.1.30 255.255.255.0
C. interface FastEthernet 0/0.30 description subinterface vlan 30
D. interface FastEthernet 0/0.30 encapsulation dot1Q 30
ip address 10.1.1.30 255.255.255.0
Answer: D
Q2. - (Topic 5)
What are two benefits of using NAT? (Choose two.)
A. NAT facilitates end-to-end communication when IPsec is enabled.
B. NAT eliminates the need to re-address all hosts that require external access.
C. NAT conserves addresses through host MAC-level multiplexing.
D. Dynamic NAT facilitates connections from the outside of the network.
E. NAT accelerates the routing process because no modifications are made on the packets.
F. NAT protects network security because private networks are not advertised.
Answer: B,F
Explanation:
By not revealing the internal IP addresses, NAT adds some security to the inside network -
> F is correct.
NAT has to modify the source IP addresses in the packets -> E is not correct.
Connection from the outside of the network through a “NAT” network is more difficult than a more network because IP addresses of inside hosts are hidden -> C is not correct.
In order for IPsec to work with NAT we need to allow additional protocols, including Internet Key Exchange (IKE), Encapsulating Security Payload (ESP) and Authentication Header (AH) -> more complex -> A is not correct.
By allocating specific public IP addresses to inside hosts, NAT eliminates the need to re- address the inside hosts -> B is correct.
NAT does conserve addresses but not through host MAC-level multiplexing. It conserves addresses by allowing many private IP addresses to use the same public IP address to go to the Internet -> C is not correct.
Q3. - (Topic 3)
Refer to the exhibit.
According to the routing table, where will the router send a packet destined for 10.1.5.65?
A. 10.1.1.2
B. 10.1.2.2
C. 10.1.3.3
D. 10.1.4.4
Answer: C
Explanation:
The destination IP address 10.1.5.65 belongs to 10.1.5.64/28, 10.1.5.64/29 & 10.1.5.64/27 subnets but the “longest prefix match” algorithm will choose the most specific subnet mask
-> the prefix “/29 will be chosen to route the packet. Therefore the next-hop should be
10.1.3.3 ->.
Q4. - (Topic 5)
Which two are features of IPv6? (Choose two.)
A. anycast
B. broadcast
C. multicast
D. podcast
E. allcast
Answer: A,C
Explanation:
IPv6 addresses are classified by the primary addressing and routing methodologies common in networking: unicast addressing, anycast addressing, and multicast addressing.
✑ A unicast address identifies a single network interface. The Internet Protocol
delivers packets sent to a unicast address to that specific interface.
✑ An anycast address is assigned to a group of interfaces, usually belonging to different nodes. A packet sent to an anycast address is delivered to just one of the member interfaces, typically the nearest host, according to the routing protocol’s definition of distance. Anycast addresses cannot be identified easily, they have the same format as unicast addresses, and differ only by their presence in the network at multiple points. Almost any unicast address can be employed as an anycast address.
✑ A multicast address is also used by multiple hosts, which acquire the multicast address destination by participating in the multicast distribution protocol among the network routers. A packet that is sent to a multicast address is delivered to all interfaces that have joined the corresponding multicast group.
Q5. - (Topic 5)
What are the alert messages generated by SNMP agents called?
A. TRAP
B. INFORM
C. GET
D. SET
Answer: A,B
Explanation:
A TRAP is a SNMP message sent from one application to another (which is typically on a remote host). Their purpose is merely to notify the other application that something has happened, has been noticed, etc. The big problem with TRAPs is that they’re
unacknowledged so you don’t actually know if the remote application received your oh-so- important message to it. SNMPv2 PDUs fixed this by introducing the notion of an INFORM, which is nothing more than an acknowledged TRAP.
Q6. - (Topic 8)
If three devices are plugged into one port on a switch and two devices are plugged into a different port, how many collision domains are on the switch?
A. 2
B. 4
C. 5
D. 6
Answer: C
Q7. - (Topic 8)
Which IPv6 header field is equivalent to the TTL?
A. Hop Limit
B. Flow Label
C. TTD
D. Hop Count
E. Scan Timer
Answer: A
Q8. - (Topic 3)
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
A. It requires the use of ARP.
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
Answer: B,D
Q9. - (Topic 8)
Which command can you enter to route all traffic that is destined for 192.168.0.0/20 to a specific interface?
A. router(config)#ip route 192.168.0.0 255.255.240.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.0 GigabitEthernet0/1
C. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
D. router(config)#ip route 192.168.0.0 255.255.255.0 GigabitEthernet0/1
Answer: A
Q10. - (Topic 8)
Which two statements about unique local IPv6 addresses are true?
A. They are identical to IPv4 private addresses.
B. They are defined by RFC 1884.
C. They use the prefix FEC0::/10
D. They use the prefix FC00::/7
E. They can be routed on the IPv6 global internet.
Answer: A,D