It is more faster and easier to pass the Cisco 200 310 pdf exam by using Real Cisco Designing for Cisco Internetwork Solutions questuins and answers. Immediate access to the Renew cisco 200 310 Exam and find the same core area ccda 200 310 official cert guide questions with professionally verified answers, then PASS your exam with a high score now.
2026 New 200-310 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-310/
Q1. What routing configuration can prevent routing loops between IGPs?
A. route filters
B. route reflectors
C. auto summarization
D. virtual links
Answer: A
Q2. What IPv4 addressing technique allows for the division of addresses into subnets of different sizes?
A. VLSM
B. RIR
C. CIDR
D. NAT
Answer: A
Q3. Which two common cable management strategies are used in high-density server deployments in the data center? (Choose two.)
A. top-of-rack
B. middle-of-rack
C. bottom-of-rack
D. beginning-of-row
E. middle-of-row
F. end-of-row
Answer: A,F
Q4. Which three options are valid Cisco STP tools used to ensure best-practice access layer design for the enterprise campus? (Choose three.)
A. Port fast
B. UDLD
C. Root Guard
D. BPDU Guard
E. Flex Links
F. SPAN
G. Ether Channel
Answer: A,C,D
Explanation:
Access layer Limit VLANs to a single closet when possible to provide the most deterministic and highly available topology.
Use RPVST+ if STP is required. It provides the best convergence.
Set trunks to ON and ON with no-negotiate
Manually prune unused VLANs to avoid broadcast propagation.
Use VTP Transparent mode, because there is little need for a common VLAN database in hierarchical networks.
Disable trunking on host ports, because it is not necessary. Doing so provides more security and speeds up Port Fast.
Consider implementing routing in the access layer to provide fast convergence and Layer 3 load balancing.
Use Cisco STP Toolkit, which provides Port Fast, Loop Guard, Root Guard, and BPDU Guard.
Q5. DRAG DROP
Answer:
Q6. What two SAN protocols will allow a customer to utilize 10GbE for SAN access? (Choose two.)
A. ISCSI
B. FCoE
C. SATA
D. Fiber Channel
E. AoE
Answer: A,B
Q7. Characterizing an existing network requires gathering as much information about the network as possible. Which of these choices describes the preferred order for the information-gathering process?
A. site and network audits, traffic analysis, existing documentation and organizational input
B. existing documentation and organizational input, site and network audits, traffic analysis
C. traffic analysis, existing documentation and organizational input, site and network audits
D. site and network audits, existing documentation and organizational input, traffic analysis
Answer: B
Explanation:
This section describes the steps necessary to characterize the existing network infrastructure and all sites. This process requires three steps:
Step 1. Gather existing documentation about the network, and query the organization to discover additional information. Organization input, a network audit, and traffic analysis provide the key information you need. (Note that existing documentation may be inaccurate.)
Step 2. Perform a network audit that adds detail to the description of the network. If possible, use traffic-analysis information to augment organizational input when you are describing the applications and protocols used in the network.
Step 3. Based on your network characterization, write a summary report that describes the health of the network. With this information, you can propose hardware and software upgrades to support the network requirements and the organizational requirements.
Q8. When designing an EIGRP network, which two things should you take into consideration? (Choose two.)
A. ASN and K values must match.
B. The neighbor command can be used to enable unicast communication.
C. The neighbor diameter cannot exceed a 15-hops limit.
D. NSSA areas can be used to redistribute external routes.
E. Neighbor relationship can be established with non-Cisco routers.
Answer: A,B
Q9. A company must deploy an IGP routing protocol on an Enterprise Network. Where should route summarization be implemented?
A. distribution
B. core
C. access
D. backbone
Answer: A
Q10. Which one of these statements is true concerning the data center distribution (aggregation) layer design?
A. With Layer 3 at the aggregation layer, the physical loops in the topology must still be managed by STP.
B. The boundary between Layer 2 and Layer 3 must reside in the multilayer switches, independent of any other devices such as firewalls or content switching devices.
C. A mix of both Layer 2 and Layer 3 access is sometimes the most optimal.
D. In a small data center, the aggregation layer can connect directly to the campus core, exchanging IP routes and MAC address tables.
Answer: C