how many questions of 210-065 dumps?

Q1. Refer to the exhibit. 

Under which tab can the registration status for the endpoint be found? 

A. Diagnostics 

B. Configuration 

C. Call Control 

D. Maintenance 

View Answer

Q2. Which statement is true about the Cisco TelePresence System 500-32 system regarding the HVAC needs for the room where it is installed? 

A. The system does not require any additional requirements above the normal HVAC requirements for the room. 

B. You must supply additional cooling requirements for the room. 

C. You must supply a room that has energy-efficient lighting to reduce the temperature of the room. 

D. The temperature of the room will be 10 to 20 degrees warmer than the rest of the building. 

View Answer

Q3. A network administrator is asked to configure a video conference using the Cisco TelePresence MCU 5300. There is a requirement for participants to start with the same layout when joining the conference. How can this goal be accomplished? 

A. Layouts cannot be customized on the MCU 5300. 

B. Configure a custom layout for each user individually. 

C. Configure a custom layout and apply the layout to all new participants. 

D. Allow each endpoint to configure its own layout. 

View Answer

Q4. Refer to the exhibit. 

You have just finished installing a 65-inch dual profile system in a multipurpose room. After powering up the entire system, only one display is used. Using the information in the exhibit, why is the second display not displaying anything from the system? 

A. The Cisco TelePresence profile systems do not support dual display. 

B. The display is not powered on. 

C. The dual display option key has not been input into the codec. 

D. The codec has the appropriate option keys installed, so either the display is not cabled correctly, the codec is configured incorrectly, or there is no input being sent to the display. 

View Answer

Q5. A technician is trying to pair a Touch 8 with a Cisco TelePresence SX20 endpoint, but the codec is not automatically listed in the touch panel. What are two possible reasons for this behavior? (Choose two.) 

A. The codec firmware version is below version TC 6.1. 

B. The codec and the Touch 8 are on separate subnets. 

C. Pairing visibility mode is not active on the codec. 

D. The codec is not compatible with a Touch 8 device. 

E. The Touch 8 is connected via the second Ethernet port on the codec. 

View Answer

Q6. Which three items should be considered when restoring a backup to a Cisco VCS Expressway? (Choose three.) 

A. A restart is required to complete the system restore process. 

B. If the backup file is encrypted, an encryption password will be needed. 

C. A valid backup configuration file must be accessible. 

D. A function SFTP server is needed for remote restore. 

E. The VCS expressway must be put into maintenance mode during the upgrade. 

F. A flash drive that is connected to the appliance can be used to restore the configuration. 

G. Cisco TMSXE can be used to process and restore backups. 

View Answer

Q7. In this item, you will need to use all information presented to you to successfully answer the question. 

The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue? 

A. The subnet mask on the codec is incorrect. 

B. The ip address of the codec is incorrect. 

C. The interface that the codec is in is in the wrong VLAN. 

D. The codec did not receive a DHCP address from the DHCP server. 

View Answer

Q8. In this item, you will need to use all information presented to you to successfully answer the question. 

Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.) 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

E. Exhibit E 

View Answer

Q9. An engineer needs to configure cascading to support additional video conference attendees. What are three capabilities when cascading? (Choose three.) 

A. Conductor automatically performs cascading. 

B. A maximum of four multipoint control units are supported. 

C. Cascading is supported for the Cisco TelePresence Server in remotely managed mode. 

D. It is possible to manually create a cascaded conference via the Cisco TelePresence MCU Management API. 

E. Cascading is supported for multipoint control units that are registered to Cisco Unified Communications Manager. 

F. All cascaded multipoint control units must be in the same location. 

View Answer

Q10. Which three features are supported by the Cisco Video Surveillance Encoding Server? (Choose three.) 

A. IP and analog cameras 

B. MPEG-2 and MPEG-4 encoding 

C. archiving 

D. motion detection 

E. clustering 

F. virtual matrix 

View Answer