Proper study guides for Refresh Cisco ROUTE Implementing Cisco IP Routing certified begins with Cisco 300 101 route preparation products which designed to deliver the Exact 300 101 dumps questions by making you pass the 9tut ccnp 300 101 test at your first time. Try the free examcollection 300 101 demo right now.
2026 New 300-101 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-101/
P.S. Exact 300-101 tutorials are available on Google Drive, GET MORE: https://drive.google.com/open?id=1BHb398qwKUUDgc3Vdghj3SxO9n6grhvU
New Cisco 300-101 Exam Dumps Collection (Question 12 - Question 21)
Q12. Which two addresses types are included in NAT?
A. inside global
B. global outside
C. outside internet
D. inside internet
E. outside local
Answer: A,E
Q13. Using the rules for IPv6 addressing, how can the address 2031:0000:240F:0000:0000:09C0:123A:121B be rewritten?
A. 2031:0:240F::09C0:123A:121B
B. 2031::240F::09C0:123A:121B
C. 2031::240F:9C0::123A:121B
D. 2031::240F:::09C0:123A:121B
Answer: A
Explanation:
Leading zeros can be truncated. For example u201c0000 can be be just written as empty. In the above example :: indicates that it has multiple 0s in that location. Typically the IPv6 format can be written down in three ways 1) compressed, 2) uncompressed and 3) fully uncompressed as shown below. All of the following are the same:
Q14. A network engineer is trying to modify an existing active NAT configuration on an IOS router by using the following command:
(config)# no ip nat pool dynamic-nat-pool 192.1.1.20 192.1.1.254 netmask 255.255.255.0 Upon entering the command on the IOS router, the following message is seen on the
console:
%Dynamic Mapping in Use, Cannot remove message or the %Pool outpool in use, cannot destroy
What is the least impactful method that the engineer can use to modify the existing IP NAT configuration?
A. Clear the IP NAT translations using the clear ip nat traffic * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.
B. Clear the IP NAT translations using the clear ip nat translation * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.
C. Clear the IP NAT translations using the reload command on the router, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.
D. Clear the IP NAT translations using the clear ip nat table * " command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.
Answer: B
Q15. Which technology uses the many-to-one method of mapping IP addresses?
A. static NAT
B. dynamic NAT
C. NAT-PT
D. PAT
Answer: D
Explanation: Overloadingu2014Maps multiple unregistered IP addresses to a single registered IP address (many to one) using different ports. This method is also known as Port Address Translation (PAT). By using overloading, thousands of users can be connected to the Internet by using only one real global IP address
Q16. Which command instructs as a PPPoE client to obtain its IP address from the PPPoE server?
A. IP address dynamic
B. ip address negotiated.
C. ip address auto negotiate.
D. ip address DHCP
Answer: B
Q17. Refer to the exhibit.
Given the partial configuration in the exhibit, which IPv6 statement is true?
A. The configuration is an example of an encrypted IPv6 VPN tunnel.
B. The configuration is an example of a one to one IPv6 tunnel.
C. The configuration is an example of a 6to4 tunnel.
D. The configuration is an example of a 4to6 tunnel.
Answer: C
Q18. A network engineer is considering enabling load balancing with EIGRP. Which consideration should be analyzed?
A. EIGRP allows a maximum of four paths across for load balancing traffic.
B. By default, EIGRP uses a default variance of 2 for load balancing.
C. EIGRP unequal path load balancing can result in routing loops.
D. By default, EIGRP performs equal cost load balancing at least across four equal cost paths.
Answer: D
Q19. At which layer does Cisco Express Forwarding use adjacency tables to populate addressing information?
A. Layer4
B. Layer 2
C. Layer 1
D. Layer 3
Answer: B
Q20. Refer to the exhibit. What two statements are true? (Choose two.)
A. Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command.
B. OSPF version 2 has been enabled to support IPv6.
C. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
D. The output was generated by the show ip interface command.
E. The router was configured with the commands: router ospf 1 network 172.16.6.0
0.0.0.255 area 1
F. This is the designated router (DR) on the FastEthernet 0/0 link.
Answer: A,C
Explanation:
OSPFv3 supports IPv6. The configuration of OSPFv3 is not a subcommand mode of the router ospf command as it is in OSPFv2 configuration. For example, instead of using the network area command to identify networks that are part of the OSPFv3 network, the interfaces are directly configured to specify that IPv6 networks are part of the OSPFv3 network.
The following describes the steps to configure OSPF for IPv6:
There are several commonly used OSPFv3 show commands, including the show ipv6 ospf [process-id] [area-id] interfacee [interface] command.
Q21. A policy needs to be implemented on Router B so that any traffic sourced from 172.16.10.0/24 will be forwarded to Router C.
Which configuration on Router B will achieve the desired effect?
A. access-list 1 permit 172.16.10.0 0.0.0.255!interface s0ip policy route-map policy!route-
map policy permit 10match ip address 1set ip next-hop 172.16.12.3
B. access-list 1 permit 172.16.10.0 0.0.0.255!interface e0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.12.2
C. access-list 1 permit 172.16.10.0 0.0.0.255!interface e0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.14.4
D. access-list 1 deny 172.16.10.0 0.0.0.255!interface s0ip policy route-map policy!route- map policy permit 10match ip address 1set ip next-hop 172.16.12.2
Answer: A
Explanation:
The u201cnext-hopu201d IP address should be the E1 interface of router C (172.16.12.3).
100% Refresh Cisco 300-101 Questions & Answers shared by Surepassexam, Get HERE: https://www.surepassexam.com/300-101-exam-dumps.html (New 487 Q&As)