Master the tshoot 300 135 Troubleshooting and Maintaining Cisco IP Networks (TSHOOT) content and be ready for exam day success quickly with this Testking ccnp tshoot 300 135 pdf training. We guarantee it!We make it a reality and give you real 300 135 tshoot questions in our Cisco ccnp tshoot 300 135 dumps pdf braindumps.Latest 100% VALID Cisco ccnp tshoot 300 135 dumps pdf Exam Questions Dumps at below page. You can use our Cisco tshoot 300 135 pdf braindumps and pass your exam.
2026 New 300-135 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-135/
Q1. - (Topic 1)
Refer to the exhibit.
How would you confirm on R1 that load balancing is actually occurring on the default-network (0.0.0.0)?
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping along with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
Answer: D
Q2. - (Topic 20)
The implementation group has been using the test bed to do an IPv6 'proof-of-concept1.
After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. IPv4 OSPF Routing
D. IPv4 EIGRP Routing
E. IPv4 Route Redistribution
F. IPv6 RIP Routing
G. IPv6 OSPF Routing
H. IPV4 and IPV6 Interoperability
I. IPv4 layer 3 security
Answer: G
Explanation:
As explained earlier, the problem is with route redistribution on R4 of not redistributing RIP routes into OSPF for IPV6.
Q3. - (Topic 11)
The implementations group has been using the test bed to do a ‘proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
Answer: A
Explanation:
On R1, we need to permit IP 209.65.200.222/30 under the access list.
Q4. - (Topic 17)
The implementations group has been using the test bed to do a ‘proof-of-concept'
that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. NTP
B. HSRP
C. IP DHCP Helper
D. IPv4 EIGRP Routing
E. IPv6 RIP Routing
F. IPv4 layer 3 security
G. Switch-to-Switch Connectivity
H. Loop Prevention
I. Access Vlans
Answer: B
Explanation:
On DSW1, related to HSRP, under VLAN 10 change the given track 1 command to instead use the track 10 command.
Q5. - (Topic 6)
The implementations group has been using the test bed to do a ‘proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been operated indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to Isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: G
Explanation:
Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with the trunk configuration on ASW1.
Q6. - (Topic 13)
The implementations group has been using the test bed to do a ‘proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: D
Explanation:
On R4, in the redistribution of EIGRP routing protocol, we need to change name of route-map to resolve the issue. It references route-map OSPF_to_EIGRP but the actual route map is called OSPF->EIGRP.
Q7. - (Topic 12)
The implementations group has been using the test bed to do a ‘proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241
address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: G
Explanation:
port security needs is configured on ASW1.
Q8. - (Topic 20)
The implementation group has been using the test bed to do an IPv6 'proof-of-concept1.
After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
Use the supported commands to isolate the cause of this fault and answer the following question.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: D
Explanation:
Start to troubleshoot this by pinging the loopback IPv6 address of DSW2 (2026::102:1). This can be pinged from DSW1, and R4, but not R3 or any other devices past that point. If we look at the diagram, we see that R4 is redistributing the OSPF and RIP IPV6 routes. However, looking at the routing table we see that R4 has the 2026::102 network in the routing table known via RIP, but that R3 does not have the route:
When we look more closely at the configuration of R4, we see that it is redistributing OSPF routes into RIP for IPv6, but the RIP routes are not being redistributed into OSPF. That is why R3 sees R4 as an IPV6 OSPF neighbor, but does not get the 2026::102 network installed.
So, problem is with route redistribution on R4.