Proper study guides for Abreast of the times Cisco Implementing Cisco Threat Control Solutions (SITCS) certified begins with Cisco 300-207 preparation products which designed to deliver the Vivid 300-207 questions by making you pass the 300-207 test at your first time. Try the free 300-207 demo right now.
2026 New 300-207 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-207/
Q1. Which sensor deployment mode does Cisco recommend when interface capacity is limited and you need to increase sensor functionality?
A. inline interface pair mode
B. inline VLAN pair mode
C. inline VLAN group mode
D. VLAN group mode
Answer: C
Q2. An ASA with an IPS module must be configured to drop traffic matching IPS signatures and block all traffic if the module fails. Which describes the correct configuration?
A. Inline Mode, Permit Traffic
B. Inline Mode, Close Traffic
C. Promiscuous Mode, Permit Traffic
D. Promiscuous Mode, Close Traffic
Answer: B
Q3. Which two conditions must you configure in an event action rule to match all IPv4 addresses in the victim range and filter on the complete subsignature range? (Choose two.)
A. Disable event action override.
B. Leave the victim address range unspecified.
C. Set the subsignature ID-range to the default.
D. Set the deny action percentage to 100.
E. Set the deny action percentage to 0.
Answer: B,C
Q4. What CLI command configures IP-based access to restrict GUI and CLI access to a Cisco Email Security appliance's administrative interface?
A. adminaccessconfig
B. sshconfig
C. sslconfig
D. ipaccessconfig
Answer: A
Q5. Which configuration mode enables a virtual sensor to monitor the session state for unidirectional traffic?
A. asymmetric mode
B. symmetric mode
C. loose mode
D. strict mode
Answer: A
Q6. A Cisco Email Security Appliance uses which message filter to drop all executable attachments entering and leaving the Cisco Email Security Appliance?
A. drop-exE. if (attachment-filename == "\.exe$") OR (attachment-filetype == "exe") { drop(); }
B. drop-exE. if (recv-listener == "InboundMail" ) AND ( (attachment-filename == "\.exe$") OR (attachment-filetype == "exe")) { drop(); }
C. drop-exe! if (attachment-filename == "\.exe$") OR (attachment-filetype == "exe") { drop(); }
D. drop-exe! if (recv-listener == "InboundMail" ) AND ( (attachment-filename == "\.exe$") OR (attachment-filetype == "exe")) { drop(); }
Answer: A
Q7. Which four statements are correct regarding management access to a Cisco Intrusion Prevention System? (Choose four.)
A. The Telnet protocol is enabled by default
B. The Telnet protocol is disabled by default
C. HTTP is enabled by default
D. HTTP is disabled by default
E. SSH is enabled by default
F. SSH is disabled by default
G. HTTPS is enabled by default
H. HTTPS is disabled by default
Answer: B,D,E,G
Q8. What is a value that Cisco ESA can use for tracing mail flow?
A. the FQDN of the source IP address
B. the FQDN of the destination IP address
C. the destination IP address
D. the source IP address
Answer: A
Q9. Which signature definition is virtual sensor 0 assigned to use?
A. rules0
B. vs0
C. sig0
D. ad0
E. ad1
F. sigl
Answer: C
Explanation:
This is the default signature. You can create multiple security policies and apply them to individual virtual sensors. A security policy is made up of a signature definition policy, an event action rules policy, and an anomaly detection policy. Cisco IPS contains a default signature definition policy called sig0, a default event action rules policy called rules0, and a default anomaly detection policy called ad0. You can assign the default policies to a virtual sensor or you can create new policies.
Q10. Which five system management protocols are supported by the Cisco Intrusion Prevention System? (Choose five.)
A. SNMPv2c
B. SNMPv1
C. SNMPv2
D. SNMPv3
E. Syslog
F. SDEE
G. SMTP
Answer: A,B,C,F,G