Pass4sure 300 208 dumps Questions are updated and all 300 208 dumps answers are verified by experts. Once you have completely prepared with our 300 208 dumps exam prep kits you will be ready for the real ccnp security sisas 300 208 official cert guide exam without a problem. We have Improved Cisco cisco 300 208 dumps study guide. PASSED cisco 300 208 First attempt! Here What I Did.


2026 New 300-208 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-208/

Q1. What three changes require restarting the application service on an ISE node?.(Choose three.) 

A. Registering a node. 

B. Changing the primary node to standalone. 

C. Promoting the administration node. 

D. Installing the root CA certificate. 

E. Changing the guest portal default port settings. 

F. Adding a network access device. 

Answer: A,B,C 

Q2. Which command is useful when troubleshooting AAA Authentication between a Cisco router and the AAA server? 

A. test aaa-server test cisco cisco123 all new-code 

B. test aaa group7 tacacs+ auth cisco123 new-code 

C. test aaa group tacacs+ cisco cisco123 new-code 

D. test aaa-server tacacs+ group7 cisco cisco123 new-code 

Answer: C 

Q3. Which statement about Cisco Management Frame Protection is true? 

A. It enables stations to remain in power-save mode, except at specified intervals to receive data from the access point. 

B. It detects spoofed MAC addresses. 

C. It identifies potential RF jamming attacks. 

D. It protects against frame and device spoofing. 

Answer: D 

Q4. Which statement about a distributed Cisco ISE deployment is true? 

A. It can support up to two monitoring Cisco ISE nodes for high availability. 

B. It can support up to three load-balanced Administration ISE nodes. 

C. Policy Service ISE nodes can be configured in a redundant failover configuration. 

D. The Active Directory servers of Cisco ISE can be configured in a load-balanced configuration. 

Answer: A 

Q5. Which two switchport commands enable MAB and allow non-802.1X capable devices to immediately run through the MAB process? (Choose two.) 

A. authentication order mab dot1x 

B. authentication order dot1x mab 

C. no authentication timer 

D. dot1x timeout tx-period 

E. authentication open 

F. mab 

Answer: A,F 

Q6. Which RADIUS attribute is used primarily to differentiate an IEEE 802.1x request from a Cisco MAB request? 

A. RADIUS Attribute (5) NAS-Port 

B. RADIUS Attribute (6) Service-Type 

C. RADIUS Attribute (7) Framed-Protocol 

D. RADIUS Attribute (61) NAS-Port-Type 

Answer: B 

Q7. Which statement about system time and NTP server configuration with Cisco ISE is true? 

A. The system time and NTP server settings can be configured centrally on the Cisco ISE. 

B. The system time can be configured centrally on the Cisco ISE, but NTP server settings must be configured individually on each ISE node. 

C. NTP server settings can be configured centrally on the Cisco ISE, but the system time must be configured individually on each ISE node. 

D. The system time and NTP server settings must be configured individually on each ISE node. 

Answer: D 

Q8. ORRECT TEXT 

The Secure-X company has started to tested the 802.1X authentication deployment using the Cisco Catalyst 3560-X layer 3 switch and the Cisco ISEvl2 appliance. Each employee desktop will be connected to the 802.1X enabled switch port and will use the Cisco AnyConnect NAM 802.1X supplicant to log in and connect to the network. 

Your particular tasks in this simulation are to create a new identity source sequence named AD_internal which will first use the Microsoft Active Directory (AD1) then use the ISE Internal User database. Once the new identity source sequence has been configured, edit the existing DotlX authentication policy to use the new AD_internal identity source sequence. 

The Microsoft Active Directory (AD1) identity store has already been successfully configured, you just need to reference it in your configuration. 

In addition to the above, you are also tasked to edit the IT users authorization policy so IT users who successfully authenticated will get the permission of the existing IT_Corp authorization profile. 

Perform this simulation by accessing the ISE GUI to perform the following tasks: 

. Create a new identity source sequence named AD_internal to first use the Microsoft Active Directory (AD1) then use the ISE Internal User database 

. Edit the existing Dot1X authentication policy to use the new AD_internal identity source sequence: 

. If authentication failed-reject the access request 

. If user is not found in AD-Drop the request without sending a response 

. If process failed-Drop the request without sending a response 

. Edit the IT users authorization policy so IT users who successfully authenticated will get the permission of the existing IT_Corp authorization profile. 

To access the ISE GUI, click the ISE icon in the topology diagram. To verify your configurations, from the ISE GUI, you should also see the Authentication Succeeded event for the it1 user after you have successfully defined the DotlX authentication policy to use the Microsoft Active Directory first then use the ISE Internal User Database to authenticate the user. And in the Authentication Succeeded event, you should see the IT_Corp authorization profile being applied to the it1 user. If your configuration is not correct and ISE can't authenticate the user against the Microsoft Active Directory, you should see the Authentication Failed event instead for the it1 user. 

Note: If you make a mistake in the Identity Source Sequence configuration, please delete the Identity Source Sequence then re-add a new one. The edit Identity Source Sequence function is not implemented in this simulation. 

Answer: Review the explanation for full configuration and solution. 

Q9. What steps must you perform to deploy a CA-signed identify certificate on an ISE device? 

A. 1. Download the CA server certificate. 

2. Generate a signing request and save it as a file. 

3. Access the CA server and submit the ISE request. 

4. Install the issued certificate on the ISE. 

B. 1. Download the CA server certificate. 

2. Generate a signing request and save it as a file. 

3. Access the CA server and submit the ISE request. 

4. Install the issued certificate on the CA server. 

C. 1. Generate a signing request and save it as a file. 

2. Download the CA server certificate. 

3. Access the ISE server and submit the CA request. 

4. Install the issued certificate on the CA server. 

D. 1. Generate a signing request and save it as a file. 

2. Download the CA server certificate. 

3. Access the CA server and submit the ISE request. 

4. Install the issued certificate on the ISE. 

Answer: D 

Q10. Refer to the exhibit. 

The links outside the TrustSec area in the given SGA architecture are unprotected. On which two links does EAC take place? (Choose two.) 

A. between switch 2 and switch 3 

B. between switch 5 and host 2 

C. between host 1 and switch 1 

D. between the authentication server and switch 4 

E. between switch 1 and switch 2 

F. between switch 1 and switch 5 

Answer: A,B