Virtual of 300-209 free practice test materials and resource for Cisco certification for consumer, Real Success Guaranteed with Updated 300-209 pdf dumps vce Materials. 100% PASS Implementing Cisco Secure Mobility Solutions (SIMOS) exam Today!
2026 New 300-209 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-209/
Q1. Which two RADIUS attributes are needed for a VRF-aware FlexVPN hub? (Choose two.)
A. ip:interface-config=ip unnumbered loobackn
B. ip:interface-config=ip vrf forwarding ivrf
C. ip:interface-config=ip src route
D. ip:interface-config=ip next hop
E. ip:interface-config=ip neighbor 0.0.0.0
Answer: A,B
Q2. Which technology can provide high availability for an SSL VPN?
A. DMVPN
B. a multiple-tunnel configuration
C. a Cisco ASA pair in active/passive failover configuration
D. certificate to tunnel group maps
Answer: C
Q3. You are configuring a Cisco IOS SSL VPN gateway to operate with DVTI support. Which command must you configure on the virtual template?
A. tunnel protection ipsec
B. ip virtual-reassembly
C. tunnel mode ipsec
D. ip unnumbered
Answer: D
Q4. Refer to the exhibit.
The IKEv2 tunnel between Router1 and Router2 is failing during session establishment. Which action will allow the session to establish correctly?
A. The address command on Router2 must be narrowed down to a /32 mask.
B. The local and remote keys on Router2 must be switched.
C. The pre-shared key must be altered to use only lowercase letters.
D. The local and remote keys on Router2 must be the same.
Answer: B
Q5. Which three configurations are required for both IPsec VTI and crypto map-based VPNs? (Choose three.)
A. transform set
B. ISAKMP policy
C. ACL that defines traffic to encrypt
D. dynamic routing protocol
E. tunnel interface
F. IPsec profile
G. PSK or PKI trustpoint with certificate
Answer: A,B,G
Q6. CORRECT TEXT
Scenario
You are the network security administrator for your organization. Your company is growing and a remote branch office is being created. You are tasked with configuring your headquarters Cisco ASA to create a site-to-site IPsec VPN connection to the branch office Cisco ISR. The branch office ISR has already been deployed and configured and you need to complete the IPsec connectivity configurations on the HQ ASA to bring the new office online.
Use the following parameters to complete your configuration using ASDM. For this exercise, not all ASDM screens are active.
. Enable IKEv1 on outside I/F for Site-to-site VPN
. Add a Connection Profile with the following parameters:
. Peer IP: 203.0.113.1
. Connection name: 203.0.113.1
. Local protected network: 10.10.9.0/24
. Remote protected network: 10.11.11.0/24
. Group Policy Name: use the default policy name supplied
. Preshared key: cisco
. Disable IKEv2
. Encryption Algorithms: use the ASA defaults
. Disable pre-configured NAT for testing of the IPsec tunnel
. Disable the outside NAT pool rule
. Establish the IPsec tunnel by sending ICMP pings from the Employee PC to the Branch Server at IP address 10.11.11.20
. Verify tunnel establishment in ASDM VPN Statistics> Sessions window pane
You have completed this exercise when you have successfully configured, established, and verified site-to-site IPsec connectivity between the ASA and the Branch ISR.
Topology
Answer: Review the explanation for detailed answer steps.
Explanation:
First, click on Configuration ->Site-to-Site VPN to bring up this screen:
Click on “allow IKE v1 Access” for the outside per the instructions as shown below:
Then click apply at the bottom of the page. This will bring up the following pop up message:
Click on Send.
Next, we need to set up the connection profile. From the connection profile tab, click on “Add”
Then, fill in the information per the instructions as shown below:
Hit OK and you should see this:
To test this, we need to disable NAT. Go to Configuration -> Firewall -> NAT rules and you should see this:
Click on Rule 1 to get the details and you will see this:
We need to uncheck the “Enable rule” button on the bottom. It might also be a good idea to uncheck the “Translate DNS replies that match the rule” but it should not be needed. Then, go back to the topology:
Click on Employee PC, and you will see a desktop with a command prompt shortcut. Use this to ping the IP address of 10.11.11.20 and you should see replies:
We can also verify by viewing the VPN Statistics -> Sessions and see the bytes in/out incrementing as shown below:
Q7. An administrator wishes to limit the networks reachable over the Anyconnect VPN tunnels. Which configuration on the ASA will correctly limit the networks reachable to 209.165.201.0/27 and 209.165.202.128/27?
A. access-list splitlist standard permit 209.165.201.0 255.255.255.224
access-list splitlist standard permit 209.165.202.128 255.255.255.224
!
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value splitlist
B. access-list splitlist standard permit 209.165.201.0 255.255.255.224
access-list splitlist standard permit 209.165.202.128 255.255.255.224
!
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
split-tunnel-policy tunnelall
split-tunnel-network-list value splitlist
C. group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list ipv4 1 209.165.201.0 255.255.255.224
split-tunnel-network-list ipv4 2 209.165.202.128 255.255.255.224
D. access-list splitlist standard permit 209.165.201.0 255.255.255.224
access-list splitlist standard permit 209.165.202.128 255.255.255.224
!
crypto anyconnect vpn-tunnel-policy tunnelspecified
crypto anyconnect vpn-tunnel-network-list splitlist
E. crypto anyconnect vpn-tunnel-policy tunnelspecified
crypto anyconnect split-tunnel-network-list ipv4 1 209.165.201.0 255.255.255.224
crypto anyconnect split-tunnel-network-list ipv4 2 209.165.202.128 255.255.255.224
Answer: A
Q8. Which two features are required when configuring a DMVPN network? (Choose two.)
A. Dynamic routing protocol
B. GRE tunnel interface
C. Next Hop Resolution Protocol
D. Dynamic crypto map
E. IPsec encryption
Answer: B,C
Q9. In DMVPN phase 2, which two EIGRP features need to be disabled on the hub to allow spoke-to-spoke communication? (Choose two.)
A. autosummary
B. split horizon
C. metric calculation using bandwidth
D. EIGRP address family
E. next-hop-self
F. default administrative distance
Answer: B,E
Q10. Which option is most effective at preventing a remote access VPN user from bypassing the corporate transparent web proxy?
A. using the proxy-server settings of the client computer to specify a PAC file for the client computer to download
B. instructing users to use the corporate proxy server for all web browsing
C. disabling split tunneling
D. permitting local LAN access
Answer: C