Exambible 300-209 Questions are updated and all 300-209 answers are verified by experts. Once you have completely prepared with our 300-209 exam prep kits you will be ready for the real 300-209 exam without a problem. We have Most recent Cisco 300-209 dumps study guide. PASSED 300-209 First attempt! Here What I Did.
2026 New 300-209 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-209/
Q1. Which two features are required when configuring a DMVPN network? (Choose two.)
A. Dynamic routing protocol
B. GRE tunnel interface
C. Next Hop Resolution Protocol
D. Dynamic crypto map
E. IPsec encryption
Answer: B,C
Q2. Which algorithm is replaced by elliptic curve cryptography in Cisco NGE?
A. 3DES
B. AES
C. DES
D. RSA
Answer: D
Q3. Which three configuration parameters are mandatory for an IKEv2 profile? (Choose three.)
A. IKEv2 proposal
B. local authentication method
C. match identity or certificate
D. IKEv2 policy
E. PKI certificate authority
F. remote authentication method
G. IKEv2 profile description
H. virtual template
Answer: B,C,F
Q4. Which equation describes an elliptic curve?
A. y3 = x3 + ax + b
B. x3 = y2 + ab + x
C. y4 = x2 + ax + b
D. y2 = x3 + ax + b
E. y2 = x2 + ax + b2
Answer: D
Q5. CORRECT TEXT
Scenario
You are the network security administrator for your organization. Your company is growing and a remote branch office is being created. You are tasked with configuring your headquarters Cisco ASA to create a site-to-site IPsec VPN connection to the branch office Cisco ISR. The branch office ISR has already been deployed and configured and you need to complete the IPsec connectivity configurations on the HQ ASA to bring the new office online.
Use the following parameters to complete your configuration using ASDM. For this exercise, not all ASDM screens are active.
. Enable IKEv1 on outside I/F for Site-to-site VPN
. Add a Connection Profile with the following parameters:
. Peer IP: 203.0.113.1
. Connection name: 203.0.113.1
. Local protected network: 10.10.9.0/24
. Remote protected network: 10.11.11.0/24
. Group Policy Name: use the default policy name supplied
. Preshared key: cisco
. Disable IKEv2
. Encryption Algorithms: use the ASA defaults
. Disable pre-configured NAT for testing of the IPsec tunnel
. Disable the outside NAT pool rule
. Establish the IPsec tunnel by sending ICMP pings from the Employee PC to the Branch Server at IP address 10.11.11.20
. Verify tunnel establishment in ASDM VPN Statistics> Sessions window pane
You have completed this exercise when you have successfully configured, established, and verified site-to-site IPsec connectivity between the ASA and the Branch ISR.
Topology
Answer: Review the explanation for detailed answer steps.
Explanation:
First, click on Configuration ->Site-to-Site VPN to bring up this screen:
Click on “allow IKE v1 Access” for the outside per the instructions as shown below:
Then click apply at the bottom of the page. This will bring up the following pop up message:
Click on Send.
Next, we need to set up the connection profile. From the connection profile tab, click on “Add”
Then, fill in the information per the instructions as shown below:
Hit OK and you should see this:
To test this, we need to disable NAT. Go to Configuration -> Firewall -> NAT rules and you should see this:
Click on Rule 1 to get the details and you will see this:
We need to uncheck the “Enable rule” button on the bottom. It might also be a good idea to uncheck the “Translate DNS replies that match the rule” but it should not be needed. Then, go back to the topology:
Click on Employee PC, and you will see a desktop with a command prompt shortcut. Use this to ping the IP address of 10.11.11.20 and you should see replies:
We can also verify by viewing the VPN Statistics -> Sessions and see the bytes in/out incrementing as shown below:
Q6. Which.protocol must be enabled on the inside interface to use cluster encryption in SSL VPN load balancing?
A. TLS
B. DTLS
C. IKEv2
D. ISAKMP
Answer: D
Q7. Which.DAP endpoint attribute checks for the matching MAC address of a client machine?
A. device
B. process
C. antispyware
D. BIA
Answer: A
Q8. Refer to the exhibit.
After the configuration is performed, which combination of devices can connect?
A. a device with an identity type of IPv4 address of 209.165.200.225 or 209.165.202.155 or a certificate with subject name of "cisco.com"
B. a device with an identity type of IPv4 address of both 209.165.200.225 and 209.165.202.155 or a certificate with subject name containing "cisco.com"
C. a device with an identity type of IPv4 address of both 209.165.200.225 and 209.165.202.155 and a certificate with subject name containing "cisco.com"
D. a device with an identity type of IPv4 address of 209.165.200.225 or 209.165.202.155 or a certificate with subject name containing "cisco.com"
Answer: D
Q9. Scenario
Your organization has just implemented a Cisco AnyConnect SSL VPN solution. Using Cisco ASDM, answer the questions regarding the implementation.
Note: Not all screens or option selections are active for this exercise.
Topology
Default_Home
What two actions will be taken on translated packets when the AnyConnect users connect to the ASA? (Choose two.)
A. No action will be taken, they will keep their original assigned addresses
B. The source address will use the outside-nat-pool
C. The source NAT type will be a static translation
D. The source NAT type will be a dynamic translation
E. DNS will be translated on rule matches
Answer: A,C
Explanation:
First, navigate to the Configuration ->NAT Rules tab to see this:
Here we see that NAT rule 2 applies to the AnyConnect clients, click on this rule for more details to see the following:
Here we see that it is a static source NAT entry, but that the Source and Destination addresses remain the original IP address so they are not translated.
Q10. Refer to the exhibit.
Which type of VPN is being configured, based on the partial configuration snippet?
A. DMVPN with dual hub
B. GET VPN with dual group member
C. FlexVPN backup gateway
D. GET VPN with COOP key server
E. FlexVPN load balancer
Answer: D