It is impossible to pass Cisco 300-370 exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Cisco 300-370 practice questions. You will get a surprising result by our Avant-garde Troubleshooting Cisco Wireless Enterprise Network practice guides.


2026 New 300-370 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-370/

Q1. A WLAN was installed at a high AP density. DTPC is lowering the transmit power of many APs too low. Which change m the DTPC transmit power threshold must be made to allow APs to globally increase AP transmit power by 3dBm? 

A. from 70 dBm to 73 dBm 

B. from -70 dBm to -73 dBm 

C. from 70 dBm to 67 dBm 

D. from -70 dBm to -67 dBm 

Answer: D 

Q2. A wireless user is experiencing connectivity issues with their Mac OS laptop. If the Mac is exhibiting the behavior of a "sticky client," how can the tech verity which AP the user is currently connected to? 

A. Hold shift while clicking the wireless icon. 

B. Hold option while clicking the wireless icon. 

C. Hold control while clicking the wireless icon. 

D. Hold command while clicking the wireless icon. 

Answer: B 

Q3. A client is failing EAP authentication and a debug shows that the server is sending an Access-Reject message. Which action must you take to resolve authentication? 

A. Verify that the Validate server certificate on the client is disabled. 

B. Verify that the client certificates are from the proper CA and server certificate. 

C. Verify that the client server certificate has the proper Windows OlDs. 

D. Verify that the user account is the same in the client certificate. 

E. Verify that the user is using the same password that is on the server 

Answer: B 

Q4. Which Cisco WLC debug command allows you to determine if the certificate process is failing in the CAPWAP messages? 

A. debug pm pki enable 

B. debug cert events enable 

C. debug capwap events enable 

D. debug capwap packet enable 

E. debug capwap errors enable 

Answer: E 

Q5. An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can be identified? 

Refer to the exhibit. 

A. one frequency hopping Bluetooth 

B. two healthy CCK and one malformed OFDM 

C. three broadband jammers 

D. two strong microwave ovens and one moderate 

Answer: B 

Q6. A network engineer has identified clients who are experiencing delays white roaming. The network is configured with WPA2-Enterpnse. AES encryption, 802 1X authentication, and Cisco Centralized Key Management Which change resolves the roaming delays? 

A. Utilize a supplicant that supports Cisco Centralized Key Management." 

B. Enable AES and TKIP encryption 

C. Disable client session timeout 

D. Install wireless device drivers from Cisco 

Answer: A 

Q7. An engineer is concerned about rogue-on-wire and wants to enable port security. Which guideline must the engineer follow? 

A. Configure Switched Port Analyzer destination ports as secure. 

B. Use 802 1x with port security to prevent MAC spoofing. 

C. Enable port security on dynamic access ports. 

D. Employ static MAC address configuration for APs with port security. 

Answer: A 

Q8. Which three steps would a network engineer use to troubleshoot an AP join problem? (Choose three.) 

A. Validate the STP configuration. 

B. Verify the ping AP from the controller. 

C. Verify the ping AP from the client. 

D. Verify that the AP is getting an address from the DHCP server. 

E. I Validate the SNMP configuration. 

F. Verify the authentication configuration parameters. 

Answer: A,B,F 

Q9. Which two statements about the WLAN are true? (Choose two) 

Refer to the exhibit. 

A. The client has a 5 GHz connection. 

B. The client has authenticated. 

C. The client is 802.11n capable. 

D. The Cisco device is a 3600 series AP. 

E. 802 11b data rates are disabled in this WLAN 

Answer: C,E 

Q10. Refer to the exhibit. 

A client reports being unable to log into the wireless network, which uses PEAPv2. Which two issues appear in the output? (Choose two) 

A. The AP has the incorrect RADIUS server address 

B. There is a problem with the client supplicant 

C. The AP has lost IP connectivity to the authentication server 

D. The authentic at ion server is misconfigured on the controller 

E. The EAP client timeout value should be increased 

F. The authentication server is misconfigured in the WLAN 

Answer: A,C