It is impossible to pass Cisco 400-151 exam without any help in the short term. Come to Exambible soon and find the most advanced, correct and guaranteed Cisco 400-151 practice questions. You will get a surprising result by our Renovate CCIE Data Center Written Exam practice guides.


2026 New 400-151 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/400-151/

Q1. Refer to the exhibit,

 

this output is observed when the troubleshooting a blade that is unable to boot from SAN which action must the cisco UCS administrator take to resolve the issue?

A. Check iSCSI intiator group pool

B. Check the LUN masking coonfiguration on the storage on array

C. Enable NPv on the fiber channel switch

D. enable on the fiber channel switch

E. Check the boot Lun ID cisco UCS boot order

F. Check zoning configuration on the fiber channel switch

Answer: B

Q2. Which three statement about ACI border leaf are true?(Choose three).

A. Only 2=32 border leaves are supported in an ACI fabric

B. Any ACI leaf can be a border leaf there is no limitation in the number of leaf switches that can be used as border leaves

C. The border leaves are ACI leaves that provide layer 3 connections to outside networks

D. The border leaves are dedicated leaf switches that support only layer 2 and layer 3 out in an ACI fabric

E. The border leaf can also be used to connect to compute, ip storage and service appliances

Answer: B,C,E

Q3. Which option lists valid configuration commands to help identify packet flow for ingress and egress IP packets and provide statistics based on packet flow when configuring a Cisco Nexus Device via the CLI?

A. Flow Record, Flow Exporter, Flow Monitor

B. sFlow Record, sFlow Exporter, sFlow Monitor

C. NetFlow Record, NetFlow Exporter, NetFlow

D. IPFix Record, IPFix Exporter, IPFix Monitor

Answer: A

Q4. Which two statements about NFS Appliance port failover and network uplink failure on Cisco UCS are true? (Choose two.)

A. To change default appliance port behavior, configure an appliance port failover policy and set the action to be taken upon uplink failure.

B. Failover must be configured on the storage side and Cisco UCS side, and it must be implemented with the correct network design while specified failover behaviors for storage controllers are kept in mind.

C. By design, Cisco UCS fabric interconnects operate as one large fabric.

D. Failover cannot be configured on the Cisco UCS side for appliance ports.

E. By default, appliance ports are shut down if the uplink that they are pinned to goes down.

Answer: A,D

Q5. In a Cisco USC B-Series environment, which option must the network adapters support to enable iSCSI boot?

A. vNIC

B. CIMC

C. iBFT

D. UEFI

E. MPIO

Answer: C

Q6. which language is used to write Cloupia Cscript?

A. Python

B. UCS director macro language

C. JAVA

D. Javascript

Answer: D

Q7. You want to make 80 Gbps of bandwidth available to your RedHat servers. Which two statements are true? (Choose two.)

A. Install 2208 lOMs, VIC 1280 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

B. Install 2204 lOMs, VIC1280 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

C. Install 2204 lOMs, V1C1240 CNAs, and create four vNICs mapped to each fabric.

D. Install 2204 IOMs, VIC 1280 CNAs, and create four vNICs mapped to each fabric.

E. Install 2204 lOMs, VIC 1240 CNAs, fabric extenders, and create four vNICs mapped to each fabric.

F. Install 2208 IOMs, VIC 1280 CNAs, fabric extenders, and create eight vNICs mapped to each fabric.

Answer: C,F

Q8. Which two statements about import and export route control in an ACI fabric are true? (Choose two.)

A. Prefixes learned from OSPF/EIGRP L30urs are never permitted inbound by default.

B. Prefixes learned from BGP L3outs cannot be filtered inbound.

C. Export route control controls if the prefixes are redistributed from MP-BGP to the egress leaf.

D. Prefixes permitted inbound are redistributed into MP-BGP at the ingress leaf.

Answer: C,D

Q9. Which mode must the Cisco MDS VSAN be configured for so that it interoperates correctly with a Brocade Fibre Channel switch that is configured for interop mode?

A. interop mode 2

B. interop mode 4

C. interop mode 3

D. native mode

E. interop mode 1

Answer: E

Q10. DRAG DROP

Drag and drop two configurations that should fail without data loss from the left column into the 2 Devices Lost column on the right.

 

Answer: