Renovate 400-151 Exam Study Guides With New Update Exam Questions

Q1. Which option require by atomic counter to be laveraged in troubleshooting endpoint connectivity?

A. Endpoint must be in different bridge domain

B. Endpoint must connect to different leaf switch

C. Endpoint must be in different endpoint group

D. end point must be in different VRF

E. Endpoint must connect to the same leaf switch

View Answer

Q2. Which three statements are considered best practice when directly connection converged network adapters to the fabric? Choose three).)

A. If the converged access switches (in the same SAN fabric or in the other) must be connected to each over Ethernet links for the purposes of LAN alternate pathing, then such links must explicitly be configured to include all FCoE VLANs. This configuration ensures to extend the scope of the Spanning Tree Protocol for FCoE VLANs to Cisco Unified Fabric and non Cisco Unified Fabric links.

B. Cisco UF links must be configured as spanning-tree edge ports.

C. If MSTP is enabled, a separate MST instance must be used for FCoE VLANs.

D. Separate FCoE VLANs must be used for FCoE in SAN-A and SAN-B.

E. A shared VLAN can be used to carry traffic for each virtual fabric in the SAN (for example, VLAN 1002 for VSAN 1, VSAN 2, and so on).

F. Cisco Unified Fabric links must be configured as access ports and FCoE VLAN must not be configured as a native VLAN.

View Answer

Q3. Which two statements about VACLs on Cisco Nexus 7000 Series Switches are true? (Choose two.)

A. A single VACL can be shared across two or more VDCs.

B. Use of VACLs requires no special license to be installed.

C. VACLs make use of IP or MAC ACLs.

D. Only options drop and forward are permitted.

View Answer

Q4. DRAG DROP

Drag and drop the enlisted four offers from the left onto the correct Cisco ONE Enterprise Cloud Suite on the right.

View Answer

Q5. Refer to the exhibit.

Which two statements about this configuration command sequence with regards to the Cisco Nexus 5500 are true. (Choose two.)

A. It configures this node to use 0EFC2A as the first 3 bytes of the FPMA.

B. It configures this node to use 0EFC2A as the last 3 bytes of the FPMA.

C. It configures this node to use FCID 0EFC2A to forward the FDISC to when an endpoint is connected.

D. It reserves this FCID so only this node can use this FCID when communicating with other Fiber Channel entities.

E. It permits this node to form FCoE ISLs only with other nodes configured for the same FC-MAP

View Answer

Q6. You configured a new appliance port, but the port has a pinning failure. Which option is possible cause?

A. The appliance port admin speed must be adjusted.

B. Appliance VLANs are missing duplicate global VLANs.

C. The appliance is configured for NPV.

D. Appliance VLANs are duplicated in global VLANs.

View Answer

Q7. In the Cisco FabricPath domain, one switch becomes the root for the multidestination tree. Cisco FabricPath switches compares which three parameters to select the root? (Choose three).)

A. Root priority

B. System ID

C. Bridge ID

D. Switch ID

E. Port ID

F. Subswitch ID

View Answer

Q8. Which three guidelines and limitations of policy-based routing are true? (Choose three).

A. An ACL used in a policy-based routing route map cannot include a deny statement.

B. A policy-based routing route map can have multiple match or set statements per route- map statement.

C. Policy-based routing and WCCPv2 are not supported on the same interface if bank chaining is disabled.

D. The same route map can be shared among different interfaces for policy-based routing as long as the interfaces belong to the same VRF instance.

E. Setting a tunnel interface or an IP address via a tunnel interface as a next hop in a policy-based routing policy is not supported.

F. A match command can refer to more than one ACL in a route map used for policy-based routing.

View Answer

Q9. The Cisco Nexus 1000v Series switches can configure traditional SPAN sessions. Which three statements about the local SPAN source ports are true? (Choose three).

A. It can be port type Ethernet, virtual Ethernet, or port-channel.

B. It can be configured to monitor the direction of the traffic.

C. It must be in the same VLAN.

D. It cannot be on a different host VEM as the destination port.

E. It cannot be a port profile.

F. It must be in the same VSAN.

View Answer

Q10. Which two statements about end-host mode are true? (Choose two.)

A. In end-host mode, if a vNIC is hard pinned to an uplink port and this uplink port goes down, the system repms the vMIC, and the vNIC go

B. End-host mode allows the fabric in interconnect to act as an end host to the network, representing all servers (hosts) connected to it through vNICs.

C. End-host mode is the default Ethernet switching mode.

D. In end-host mode, the fabric interconnect runs the 5pann,ng Tree Protocol to avoid loops.

E. In end-host mode, if a vNIC is hard pinned to an uplink port and this uplink port goes down, the system repins the vNIC but the vNIC remain down until manual intervention.

View Answer