All About 100% Correct 400-201 braindumps

Q1. An operations engineer wants to manually optimize the MPLS Traffic Engineering tunnels. Which Cisco IOS EXEC command should the engineer apply? 

A. tunnel mpls traffic-eng autoroute destination 

B. tunnel mpls traffic-eng path-option lowest _number dynamic 

C. mpls traffic-eng reoptimize lockdown 

D. mpls traffic-eng multicast-intact 

E. mpls traffic-eng reoptimize 

View Answer

Q2. Refer to the exhibit. R3 cannot install a route to R1-R2 subnet 2001:1:155:12::/64. Which action resolves this issue? 

A. Add the redistribute ospf 1 include-connected command under the ipv6 router eigrp 10 process. 

B. For the OSPF process, add the no shutdown command. 

C. For prefix-list OSPF_INTO_EIGRP seq 20, replace the prefix with 2001:155:1:12::/64. 

D. For route-map OSPF_INTO_EIGRP, add the set metric 1000 1 255 1 1500 command. 

View Answer

Q3. A Service Provider connects to a client site that has two CEs. These CEs have a backdoor link for backup. OSPF is used as the routing protocol in this environment. You want to ensure that client traffic prefers the service provider connections for routing instead of the secondary connection. Which option describes the default behavior and the action that accomplishes your goal? 

A. The routes to the Service Provider are not preferred, due to the increased OSPF cost through the service provider network. Ensure that the cost on the links to the service provider are lower than the secondary connection. 

B. The routes to the Service Provider are seen as external type 1 in the OSPF database. Configure a domain ID that is the same across all PEs, to ensure that customers see routes as intra-area. 

C. The routes to the Service Provider are seen as inter-area OSPF routes through the network. Configure a sham link to create a new intra-area path across the service provider network between the PE routers that service the client. 

D. The routes to the Service Provider are seen as equal and cause nondeterministic traffic patterns. Ensure that the secondary connection has a higher cost than the links to the service provider. 

View Answer

Q4. Refer to the exhibit. 

The vrf MAINT has been provisioned and used by the Service Provider management network. The engineer discovers that syslog messages are not being received on the syslog server. IP reachability has been validated using ping. Which issue in the configuration must be corrected? 

A. logging on must include the vrf MAINT keyword. 

B. logging host must include the vrf MAINT keyword. 

C. The logging facility must be configured for syslog processing. 

D. The route targets that are configured do not match the route distinguisher. 

View Answer

Q5. Which two frame types are correct when configuring T3 interfaces? (Choose two.) 

A. M23 

B. G.832 

C. Extended Super Frame 

D. C-bit parity 

E. G.751 

F. Super Frame 

View Answer

Q6. DRAG DROP 

Drag and drop each fast detection mechanism on the left to its definition on the right. 

View Answer

Q7. A network engineer needs to connect two core switches that use Gigabit Ethernet interfaces in an MPLS backbone and that are separated by a distance of 60 km. Which Cisco GBIC achieves this goal? 

A. Cisco 1000BASE-T GBIC 

B. Cisco 1000BASE-SX GBIC 

C. Cisco 1000BASE-LX/LH GBIC 

D. Cisco 1000BASE-ZX GBIC 

View Answer

Q8. What is the PPMP label used for? 

A. for the ingress replication model with BIDIR-PIM in an overlay model 

B. only for the inter-AS mVPN models that use mLDP 

C. for the partitioned mVPN model with PIM signaling in an overlay model 

D. only for unicast over MPLS VPN 

E. for all the default MDT and mVPN models 

View Answer

Q9. The following MPP configuration is applied on RA router: RP/0/RSP0/CPU0:RA#sh running-config control-plane 

control-plane 

management-plane 

inband 

interface TenGigE 0/0/0/0 

allow SSH peer 

address ipv4 5.0.0.0/8 

Which two pieces of information are correct in regards to management traffic on RA router? (Choose two) 

A. SNMP traps going out on TenGigE 0/0/0/0 interface are dropped. 

B. SNMP polling coming through TenGigE 0/0/0/0 interface are dropped. 

C. Telnet connections coming through MgmtEth0/RSP0/CPU0/0 interface are accepted. 

D. SSH connections coming through TenGigE 0/0/0/0 interface from 5.5.5.5 host are accepted. 

E. TACACS traffic going through TenGigE 0/0/0/0 interface are dropped. 

View Answer

Q10. Which two statements about 10 Gigabit Ethernet WAN PHY mode are true? (Choose two.) 

A. The signal maps to an OC-192c/STM-64c payload. 

B. The nominal speed is 9.95328 Gbps. 

C. It is compatible with Packet Ethernet over SONET. 

D. The signal maps to an OC-768c/STM-256c payload. 

E. It is compatible with Packet over SONET. 

F. The nominal speed is 10.3125 Gbps. 

View Answer