Your success in Cisco cisco 300 206 is our sole target and we develop all our 300 206 senss braindumps in a way that facilitates the attainment of this target. Not only is our cisco 300 206 study material the best you can find, it is also the most detailed and the most updated. cisco 300 206 Practice Exams for Cisco CCNP Security cisco 300 206 are written to the highest standards of technical accuracy.


2026 New 300-206 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/300-206/

Q1. Which two statements about Cisco IDS are true? (Choose two.) 

A. It is preferred for detection-only deployment. 

B. It is used for installations that require strong network-based protection and that include sensor tuning. 

C. It is used to boost sensor sensitivity at the expense of false positives. 

D. It is used to monitor critical systems and to avoid false positives that block traffic. 

E. It is used primarily to inspect egress traffic, to filter outgoing threats. 

Answer: A,D 

Q2. CORRECT TEXT 

You are a network security engineer for the Secure-X network. You have been tasked with implementing dynamic network object NAT with PAT on a Cisco ASA. 

You must configure the Cisco ASA such that the source IP addresses of all internal hosts are translated to a single IP address (using different ports) when the internal hosts access the Internet. 

To successfully complete this activity, you must perform the following tasks: 

. Use the Cisco ASDM GUI on the Admin PC to configure dynamic network object NAT with PAT using the following parameters: 

. Network object name: Internal-Networks 

. IP subnet: 10.10.0.0/16 

. Translated IP address: 192.0.2.100 

. Source interface: inside 

. Destination interface: outside 

NOTE: The object (TRANSLATED-INSIDE-HOSTS) for this translated IP address has already been created for your use in this activity. 

NOTE: Not all ASDM screens are active for this exercise. 

NOTE: Login credentials are not needed for this simulation. 

. In the Cisco ASDM, display and view the auto-generated NAT rule. 

. From the Employee PC, generate traffic to SP-SRV by opening a browser and navigating to http://sp-srv.sp.public. 

. From the Guest PC, generate traffic to SP-SRV by opening a browser and navigating to http://sp-srv.sp.public. 

. At the CLI of the Cisco ASA, display your NAT configuration. You should see the configured policy and statistics for translated packets. 

. At the CLI of the Cisco ASA, display the translation table. You should see dynamic translations for the Employee PC and the Guest PC. Both inside IP addresses translate to the same IP address, but using different ports. 

You have completed this exercise when you have configured and successfully tested dynamic network object NAT with PAT. 

Answer: Use the following configuration as per exhibit in explanation. 

Q3. Which two features does Cisco Security Manager provide? (Choose two.) 

A. Configuration and policy deployment before device discovery 

B. Health and performance monitoring 

C. Event management and alerting 

D. Command line menu for troubleshooting 

E. Ticketing management and tracking 

Answer: B,C 

Q4. Which statement is true of the logging configuration on the Cisco ASA? 

A. The contents of the internal buffer will be saved to an FTP server before the buffer is overwritten. 

B. The contents of the internal buffer will be saved to flash memory before the buffer is overwritten. 

C. System log messages with a severity level of six and higher will be logged to the internal buffer. 

D. System log messages with a severity level of six and lower will be logged to the internal buffer. 

Answer: C 

Explanation: 

\psfHome.TrashScreen Shot 2015-06-17 at 5.26.32 PM.png 

Q5. CORRECT TEXT 

Answer: Please check the steps in explanation part below: 

Q6. When you set a Cisco IOS Router as an SSH server, which command specifies the RSA public key of the remote peer when you set the SSH server to perform RSA-based authentication? 

A. router(config-ssh-pubkey-user)#key 

B. router(conf-ssh-pubkey-user)#key-string 

C. router(config-ssh-pubkey)#key-string 

D. router(conf-ssh-pubkey-user)#key-string enable ssh 

Answer: B 

Q7. Which Cisco TrustSec role does a Cisco ASA firewall serve within an identity architecture? 

A. Access Requester 

B. Policy Decision Point 

C. Policy Information Point 

D. Policy Administration Point 

E. Policy Enforcement Point 

Answer: E

Q8. Which feature can suppress packet flooding in a network? 

A. PortFast 

B. BPDU guard 

C. Dynamic ARP Inspection 

D. storm control 

Answer: D 

Q9. A Cisco ASA is configured in multiple context mode and has two user-defined contexts—Context_A and Context_B. From which context are device logging messages sent? 

A. Admin 

B. Context_A 

C. Context_B 

D. System 

Answer: A 

Q10. An administrator is deploying port-security to restrict traffic from certain ports to specific MAC addresses. Which two considerations must an administrator take into account when using the switchport port-security mac-address sticky command? (Choose two.) 

A. The configuration will be updated with MAC addresses from traffic seen ingressing the port. The configuration will automatically be saved to NVRAM if no other changes to the configuration have been made. 

B. The configuration will be updated with MAC addresses from traffic seen ingressing the port. The configuration will not automatically be saved to NVRAM. 

C. Only MAC addresses with the 5th most significant bit of the address (the 'sticky' bit) set to 1 will be learned. 

D. If configured on a trunk port without the 'vlan' keyword, it will apply to all vlans. 

E. If configured on a trunk port without the 'vlan' keyword, it will apply only to the native vlan. 

Answer: B,E