Verified CCNP Data Center 642-980 pdf

Q1. Which statement is true regarding how OTV edge devices will react based on the configuration of the VLANs being extended across the overlay network? 

A. Any VLANs not extended will not be populated in the local OTV route table. 

B. Only the same-site edge AED device controls which VLANs are to be extended. 

C. Any extended VLANs will not be populated in the remote OTV route table. 

D. By default, all VLANs on an edge device will be extended. 

View Answer

Q2. Which CLI command can tell which switch is on the other side of port channel 2 that is trunking VSAN 5? 

A. show topology vsan 5 

B. show interface port-channel 2 trunk vsan 5 

C. show interface port-channel 2 vsan 5 peer-info 

D. show fcs vsan 5 

E. show fspf database vsan 5 interface port-channel 2 

View Answer

Q3. Which statement is true regarding Cisco FabricPath? 

A. It is necessary to first install the Cisco FabricPath feature set in the default VDC. 

B. Cisco FabricPath is only available on Cisco Nexus 7010 Switches with the Supervisor 2 engine. 

C. Cisco FabricPath cannot be disabled explicitly for a specific VDC. 

D. If the Cisco FabricPath feature is not installed, the fabricpath keyword will be available in the feature-set command. 

View Answer

Q4. What is one requirement for running FabricPath on a Cisco Nexus 7000 Series switches? 

A. You must have an F Series module 

B. You must run NX-OS version 4.2 to run FabrciPath 

C. ISSU needs to be disabled to run FabricPath 

D. LAN_TRANSPORT_SERVICES_PKG license needs to be installed to run FabrciPath 

View Answer

Q5. Refer to the exhibit. 

In the initial SAN deployment or after topology changes in the SAN, some hosts cannot communicate with storage. What are three possible causes of the problem? (Choose three.) 

A. misconfigured fabric timers 

B. misconfigured port parameters 

C. VSAN pruning 

D. VSAN trunking issues 

E. VLAN problems 

F. mismatched zoning 

View Answer

Q6. On the secondary vPC switch, under which circumstance does the vPC autorecovery feature not bring up the vPC member ports? 

A. Peer link fails, and subsequently, the peer-keepalive link fails. 

B. Peer link is up, and the peer-keepalive link fails. 

C. Both vPC peers are reloaded, and the primary does not come back up. 

D. Peer link fails, and subsequently, the primary switch fails. 

View Answer

Q7. Which statement is true regarding the admin VDC? 

A. All licensed features and feature sets must be enabled from the admin VDC. 

B. Fabric extenders connectedto the admin VDC must be statically pinned. 

C. Only the mgmt 0 interface is allocated to the admin VDC. 

D. All interfaces other than mgmt 0 are allocated to the default VDC. 

E. The admin context can only be created on Supervisor 2/2E. 

F. The admin VDC is a new feature in Cisco NX-OS version 6.0. 

View Answer

Q8. Refer to the exhibit. 

A customer is having problems with NPV. Which of these is the cause of the problem? 

A. No server was requested or received by the FLOGI database. 

B. One external link must be up for server interface to be up. 

C. Internal links are down and must be up for the server interface to be up. 

D. VSANs are misconfigured on the upstream ports. 

E. VLANs are misconfigured on the upstream ports. 

View Answer

Q9. Refer to the exhibit. 

A customer is having a problem with NPV. Which of these is the cause of the problem? 

A. No server was requested or received by the FLOGI database. 

B. One external link must be up for server interface to be up. 

C. Multiple external links must be up for the server to come up. 

D. Internal links are down and must be up for the server interface to be up. 

View Answer

Q10. Which two commands can you issue on a Cisco Nexus 5548UP Switch to determine which interfaces are connected to fabric extenders? (Choose two.) 

A. show fex-fabric interface 

B. show fex 

C. show fex fex-id 

D. show fex interface 

E. show fex detail 

View Answer