The Renew Guide To 648-247 examcollection

Q1. How should NTP be implemented in a Cisco Physical Access Control Gateway design?

A. NTP is not required.

B. NTP should be configured for the Cisco PAM Server only.

C. NTP should be configured for Cisco Physical Access Control Gateways only.

D. NTP should be configured on Cisco PAM Servers and gateways.

View Answer

Q2. Is it possible to create a function that does not normally exist in the Cisco PAM by using log codes?

A. No, this is not possible

B. Yes, by creating a global I/O and configuring associations with log codes

C. Yes, by URL triggers to update the log codes

D. Yes, by using built-in device I/O rules

View Answer

Q3. In Cisco PAM, how do you configure items such as doors, events, and reports?

A. via a web browser and logging into the Cisco PAM Server Administration web page

B. by using the Cisco PAM Java Client

C. Cisco PAM is configured using Cisco VSOM

D. by using the Cisco PAM EDI Studio application

View Answer

Q4. How can Cisco Physical Access Control (Cisco PAC) modules directly interface with fire alarm systems for door release function?

A. Cisco PAC modules should not directly interface with firm alarm systems for door release functions.

B. Cisco PAC modules can directly interface with fire alarm systems for door release functions via the CAN bus.

C. Cisco PAC modules can directly interface with fire alarm systems for door release functions via open APIs in the Cisco PAM.

D. Cisco PAC modules cannot directly interface with fire alarm systems for door release functions because the modules are digital and fire alarm systems are analog.

View Answer

Q5. Does the Cisco Physical Access Control Gateway have the ability to power other devices?

A. Yes, the gateway has a total of 650 milliamperes (ma) of available power for readers, locks, and other devices.

B. Yes, the gateway can power one reader, one lock, and one additional module.

C. Yes, the gateway uses the Eth1 port to pass PoE.

D. No, the gateway cannot power any other devices.

View Answer

Q6. What is the default schedule to specify how often EDI data will be synchronized with the Cisco PAM, and can it be customized?

A. The default schedule is every 60 minutes and customizable.

B. The default schedule is every 60 minutes and not customizable.

C. The default schedule is every 120 seconds and customizable.

D. The default schedule is every 120 seconds and not customizable.

View Answer

Q7. What are the various ways to provide power to the access control reader, input, and output modules?

A. PoE only

B. 12 VAC only

C. 12 to 24 VDC only

D. PoE or 12 to 24 VDC

View Answer

Q8. Refer to the exhibit.

One or more expansion modules is connected to the Cisco Access Gateway via a CAN bus. How should the CAN bus wires be connected after the last module in the chain?

A. The CAN bus wires should be looped back to the Cisco Access Gateway.

B. The CAN bus wires should be twisted together and tucked away.

C. The CAN bus wires should be plugged into a Layer 2 Ethernet switch.

D. The CAN bus wires should be terminated with a high-impedance resistor.

View Answer

Q9. A gateway is reporting unstable or flapping connectivity. INPUT 1 is rapidly flapping between "up" and "down." What is the most likely cause?

A. The input is configured as supervised, when it should be unsupervised.

B. The wires are dirty or improperly seated in the termination block.

C. The gateway is defective and should be RMA.

D. The input on the gateway is configured as supervised, and the wires could be dirty or improperly seated in the termination block.

View Answer

Q10. In a Cisco PAM schedule, what are the available actions for a Schedule typE. Access Policy?

A. Permit only

B. Deny only

C. Custom only

D. Permit and Deny only

E. Permit, Deny, and Custom

View Answer