Top Tips Of Regenerate HPE6-A45 Answers

NEW QUESTION 1
Refer to the exhibit.

Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?

• A. asymmetric routing introduced by a routing protocol
• B. an issue with VLAN mismatch
• C. mismatched subnet mask on the VLAN for the link
• D. a jumbo frame mismatch

Answer: A

NEW QUESTION 2
A network administrator needs to create a backplane stack with four AOS-Switches. The administrator wants to choose which switch becomes the commander. Which procedure meets those needs?

• A. Boot all of the switches at the same time and then connect the backplane stacking link
• B. Then, access the desired commander, and make sure it has member ID 1.
• C. Configure backplane switches settings on each switch while disconnecte
• D. Make sure the desired commander has priority value 1. Then, connect the switches.
• E. Boot up the desired commander first and make sure stacking is enabled on i
• F. Then, connect the stacking links and boot the other switches.
• G. Configure backplane switching settings on each switch while disconnecte
• H. Make sure the desired commander has member ID 1. Then, connect the switches.

Answer: D

NEW QUESTION 3
A network administrator applies port security to a port with the send-alarm action. What does the switch do if it detects traffic from an unauthorized MAC address on the port?

• A. It disables the port, but sends no SNMP trap.
• B. It forwards the traffic, and it logs an event.
• C. It blocks the traffic, but sends no SNMP trap.
• D. It blocks the traffic, and it sends an SNMP tra

Answer: A

NEW QUESTION 4
Which switches can be deployed in a mesh topology for backplane stacking?

• A. Aruba 2920 switches
• B. Aruba 2930F switches
• C. Aruba 2930M switches
• D. Aruba 3810 switches

Answer: D

NEW QUESTION 5
Two AOS-Switches connect on VLAN 10 in OSPF Area 1, which is defined as a stub area on both. Which mismatch can cause OSPF routers to lose adjacency?

• A. The administrator adds the backbone area to just one of the routers.
• B. The administrator enables graceful restart, or nonstop switching, on just one of the routers.
• C. The administrator enables jumbo frames on VLAN 10 on just one of the routers.
• D. The administrator adds the no-summary option to Area 1 on just one of the router

Answer: B

NEW QUESTION 6
Refer to the exhibit.

An administrator created a backplane stack with the plug-and-play method, and did not alter the default backplane stacking settings. Later, two backplane stacking links failed, as shown in the exhibit.
What happens to the backplane stack after the failures?

• A. The standby becomes the commander of its fragment, which remains activ
• B. The fragment with the commander becomes inactive.
• C. The fragment that contains the commander operates at Layer 2 and layer 3, and the other fragment operates at layer 2 only.
• D. The fragment that contains the commander remains active, and the fragment with the standby member is disabled.
• E. The standby becomes the commander of its fragmen
• F. Both fragments remain active and operate at both Layer 2 and Layer 3.

Answer: D

NEW QUESTION 7
What is the purpose of the captive portal URL hash key on an AOS-Switch?

• A. It specifies the captive portal URL and conceals the setting in the config.
• B. It authenticates guest users based on the password the users enter in the portal.
• C. It does not let users alter the URL that redirects them to the portal.
• D. It encrypts and secures the RADIUS messages that the AOS-Switch sends to ClearPas

Answer: C

NEW QUESTION 8
A network administrator configures DHCP snooping on VLAN 2. How does the switch handle DHCP traffic that arrives in this VLAN on an untrusted interface?

• A. It accepts packets from a DHCP server, but drops client packets.
• B. It drops all DHCP traffic and logs a security event.
• C. It accepts both client and server packets as long as they match the DHCP binding table.
• D. It accepts client packets, but drops packets from a DHCP serve

Answer: A

NEW QUESTION 9
A network administrator needs to set up an AOS-Switch to use port-based tunneled node for connected
devices. However, the administrator wants the switch to forward traffic without tunneling if it cannot reach a tunneled- node server.
What should the administrator do?

• A. Apply the tunneled-node profile to ports, and set the local-switching-fallback option.
• B. Make sure that the switch has an IP address on the untagged VLAN assigned to the ports.
• C. Configure a local switching profile on the Mobility Controller that acts as tunneled-node server.
• D. Set the switch to role-based tunneled node, and make sure it uses the default initial user rol

Answer: D

NEW QUESTION 10
Refer to the exhibits. Exhibit 1

Exhibit 2

Switch-1 has a power issue that causes it to fail. When Switch-1 comes back up, endpoints lose connectivity for a few minutes. The network administrator decides to enter this command on Switch-1:
Switch-1 (config)# vlan 10 vrrp vrid 10 preempt-delay-time 120
Exhibit 2 shows the VRRP configuration just after the change. What is the effect of this change?

• A. Switch-1 and Switch-2 both become Master in their own VRRP virtual router due to the delay timer mismatc
• B. The mismatch must be fixed.
• C. Switch-1 now waits to take over as Master if it fails and recover
• D. This should prevent the connectivity issue from occurring again.
• E. Switch-1 experiences an internal error in the VRRP proces
• F. This error causes Switch-2 to take over as Master for VLAN 2.
• G. Switch-1 continues to act as it did before the preempt delay time was se
• H. Administrators must plan additional changes to fix the issue.

Answer: C

NEW QUESTION 11
A company has a Unified Communications and Collaboration (UCC) solution. Users run softphones on their desktops and laptops.
The UCC solution is configured to use a certain range of Layer 4 ports for VoIP traffic. The user devices connect to AOS-Switches.
A network administrator needs to configure the AOS-Switches to prioritize only the VoIP traffic. Where can the administrator configure a DSCP value to meet this goal?

• A. in a global UDP port-based QoS policy
• B. on the interfaces through which the VoIP traffic is forwarded
• C. on the interfaces that connect to the user devices
• D. on the VLAN to which the user devices are assigned

Answer: B

NEW QUESTION 12
A company has a wireless Aruba solution and wired users that connect to AOS-Switches. The company wants deep insight into the types of applications that wired users run. The company also wants more control over the traffic. What can the company do to meet these goals?

• A. Use tunneled node to send traffic through an Aruba Mobility Controller
• B. Configure extended IP ACLs on the AOS-Switches to filter the traffic.
• C. Configure RMON receives on the switches.
• D. Set up remote traffic mirroring between the AOS-Switches and Aruba Mobility Controller

Answer: A

NEW QUESTION 13
Refer to the exhibit.

Every switch in the exhibit will route traffic. The company requires a topology in which failover for switch-to-switch links is exclusively handled by the routing protocol and occurs as quickly as possible. Which topology should the administrator use?

• A. A
• B. B
• C. C
• D. D

Answer: B

NEW QUESTION 14
Refer to the exhibit.

The company wants the fastest convergence and best load sharing of traffic over the links between Switch-1 and the VSF fabric. Which technology should the network administrator implement on these links?

• A. RPVST+
• B. MSTP
• C. loop protection
• D. LACP

Answer: D

NEW QUESTION 15
Refer to the exhibits. Exhibit 1

Exhibit 2

The network administrator needs to set up BGP between the two company switches, Switch-1 and Switch-2. The BGP connection does not establish. Based on the exhibits, what does the administrator need to do to fix the issue?

• A. Set the update source for the neighbor to the local loopback interface on each switch.
• B. Enter the network command for 10.0.0.0/24 in the router BGP mode on each switch.
• C. Enable the multihop option for the neighbor on each of the switches.
• D. Enable BGP on the interfaces that the switches use to reach each othe

Answer: A

NEW QUESTION 16
Network administrators need to configure a BGP neighbor on an AOS-Switch. What defines the neighbor as an iBGP neighbor?

• A. It has BGP synchronization enabled.
• B. It has an AS number in the range 12 to 64535.
• C. Its update source is set to a private company IP address.
• D. Its remote-AS is the same as the AOS-Switch BGP A

Answer: D

NEW QUESTION 17
An administrator wants to ensure that an AOS-Switch forwards all traffic that it receives on interface 1 with high priority.
- Switches should also communicate the high priority to other switches across the traffic path.
- The switch has type of service disabled.
- The administrator plans to apply 802.1p priority 5 to interface 1.
What should the administrator check to ensure that the configuration will work properly?

• A. Interface 1 receives traffic with a tag.
• B. The AOS-Switch is configured to use eight queues.
• C. The forwarding path for the traffic uses VLAN tags.
• D. An 802.1p-to-DSCP map exists for priority 5.

Answer: A

NEW QUESTION 18
Refer to the exhibit.

Both Switch-1 and Switch-2 redistribute RIP routes into OSPF. The network administrator wants routers in Area 1 to receive the redistributed routes from Switch-1 but not from Switch-2.
What should the administrator do to achieve this goal?

• A. Configure Area 1 as a stub area, with no summaries on Switch-2.
• B. Configure Area 1 as a stub area, and import the routes with a low metric on Switch-2.
• C. Configure Area 1 as a Not So Stubby Area (NSSA) on all routing devices in Area 1.
• D. Configure a subnet range for Area 1 on Switch-2, and set the no-advertise optio

Answer: C

NEW QUESTION 19
A company has AOS-switches, Aruba ClearPass, and Aruba AirWave. A network administrator needs to find the source of a performance issue that often occurs at the start of the day and early in the afternoon. Which action is likely to give the administrator the most useful information for the investigation?

• A. Access the Network Device view on ClearPass.
• B. Use the configuration audit tool on AirWave.
• C. View the current running config on each switch.
• D. View usage patterns on the switches on AirWav

Answer: A

NEW QUESTION 20
Refer to the exhibits.

Exhibit 2

The network administrator configures the commands shown in Exhibit 2. Which mismatch will cause an issue?

• A. the mismatch between the key IDs specified in chain10 and chain11 on Switch-1
• B. the mismatch between the key-strings in the chains for VLAN 10 and VLAN 11 on Switch-1
• C. the mismatch between the chain names associated with VLAN 11 on Switch-1 and on Switch-3
• D. the mismatch between the key-strings associated with VLAN 10 on Switch-1 and on Switch-2

Answer: D

NEW QUESTION 21
Refer to the exhibits.
Exhibit 1

Exhibit 2

Exhibit 1 shows a portion of the BGP routing table when the BGP solution was first deployed. Exhibit 2 shows the same portion at the current time. What can explain the current state?

• A. Due to changes in the private network, Switch-1 can no longer reach 192.168.2.1.
• B. Switch-1 can no longer reach ISP 1 at 192.168.1.1.
• C. Due to changes at ISP 1, Switch-1 now selects a different best route.
• D. An administrator has applied a route map on Switch-1 that filters advertised route

Answer: C

NEW QUESTION 22
A company has AOS-Switches deployed at sites with inexperienced IT staff. The main office network administrators want to track if configurations change on branch switches.
What should be set up for this purpose?

• A. an SNMP trap
• B. an RMON alarm
• C. an IP SLA profile
• D. an auto-config server

Answer: A

NEW QUESTION 23
Refer to the exhibits. Exhibit 1.

Exhibit 2.

The exhibits show the current operational state for routes on Switch-3 to send all traffic to 172.16.0.0/16 through Switch- 2 during normal operation.
Which single configuration change creates the desired behavior?

• A. Set a cost in the redistribute static command on Switch-2 to change the external LSA metric.
• B. Change the OSPF external metric type to 1 on Switch-1, and set a cost on Switch-3 VLAN 104.
• C. Change the OSPF external metric type to 1 on Switch-1, and set a cost on Switch-3 VLAN 108.
• D. Set a cost in the redistribute static command on Switch-1 to change the external LSA metri

Answer: D

NEW QUESTION 24
......