It is more faster and easier to pass the Cisco cisco 100 105 pdf exam by using 100% Guarantee Cisco Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) questuins and answers. Immediate access to the Most up-to-date cisco 100 105 pdf Exam and find the same core area cisco 100 105 pdf questions with professionally verified answers, then PASS your exam with a high score now.
2026 New 100-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/100-105/
Q1. - (Topic 5)
Refer to the exhibit.
An administrator replaced the 10/100 Mb NIC in a desktop PC with a 1 Gb NIC and now the PC will not connect to the network. The administrator began troubleshooting on the switch. Using the switch output shown, what is the cause of the problem?
A. Speed is set to 100Mb/s.
B. Input flow control is off.
C. Encapsulation is set to ARPA.
D. The port is administratively down.
E. The counters have never been cleared.
Answer: A
Explanation:
For PC to switch connectivity, the speed settings must match. In this case, the 1 Gb NIC will not be able to communicate with a 100Mb fast Ethernet interface, unless the 1Gb NIC can be configured to connect at 100Mb.
Q2. - (Topic 5)
Refer to the exhibit.
A network administrator has configured a Catalyst 2950 switch for remote management by pasting into the console the configuration commands that are shown in the exhibit. However, a Telnet session cannot be successfully established from a remote host. What should be done to fix this problem?
A. Change the first line to interface fastethernet 0/1.
B. Change the first line to interface vlan 0/1.
C. Change the fifth line to ip default-gateway 192.168.17.241.
D. Change the fifth line to ip route 0.0.0.0 0.0.0.0 192.168.17.1.
E. Change the sixth line to line con 0.
Answer: C
Explanation:
The default gateway must reside on the same IP subnet as the device. Here, the subnet mask for the VLAN interface is /228. Only choice C will fix this issue, as then the default gateway is on the same subnet as the 2950.
Q3. - (Topic 2)
A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the switch (collision, broadcast)?
A. 4, 48
B. 48, 4
C. 48, 1
D. 1, 48
E. 4, 1
Answer: B
Explanation:
A switch uses a separate collision domain for each port, and each VLAN is a separate broadcast domain.
Topic 3, Routing Fundamentals
Q4. - (Topic 3)
Which characteristics are representative of a link-state routing protocol? (Choose three.)
A. provides common view of entire topology
B. exchanges routing tables with neighbors C. calculates shortest path
D. utilizes event-triggered updates
E. utilizes frequent periodic updates
Answer: A,C,D
Explanation:
Each of routers running link-state routing protocol learns paths to all the destinations in its
“area” so we can say although it is a bit unclear.
Link-state routing protocols generate routing updates only (not the whole routing table)
when a change occurs in the network topology so
Link-state routing protocol like OSPF uses Dijkstra algorithm to calculate the shortest path -> .
Unlike Distance vector routing protocol (which utilizes frequent periodic updates), link-state
routing protocol utilizes event-triggered updates (only sends update when a change occurs)
->
Q5. - (Topic 3)
A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem?
Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly.
B. The OSPF area is configured improperly.
C. The network wildcard mask is configured improperly.
D. The network number is configured improperly.
E. The AS is configured improperly.
F. The network subnet mask is configured improperly.
Answer: C
Explanation:
When configuring OSPF, the mask used for the network statement is a wildcard mask similar to an access list. In this specific example, the correct syntax would have been “network 10.0.0.0 0.0.0.255 area 0.”
Q6. - (Topic 1)
What are two common TCP applications? (Choose two.)
A. TFTP
B. SMTP
C. SNMP
D. FTP
E. DNS
Answer: B,D
Explanation:
SMTP uses TCP port 25, while FTP uses TCP ports 20 and 21.
Reference: http://pentestlab.wordpress.com/2012/03/05/common-tcpip-ports/
Q7. - (Topic 3)
Refer to the exhibit.
Which two statements are correct? (Choose two.)
A. This is a default route.
B. Adding the subnet mask is optional for the ip route command.
C. This will allow any host on the 172.16.1.0 network to reach all known destinations beyond RouterA.
D. This command is incorrect, it needs to specify the interface, such as s0/0/0 rather than an IP address.
E. The same command needs to be entered on RouterA so that hosts on the 172.16.1.0 network can reach network 10.0.0.0.
Answer: A,C
Explanation:
This is obviously the default route which is set between the routers and since it is entered in such a manner that it ensures connectivity between the stub network and any host lying beyond RouterA.
Q8. - (Topic 3)
On a live network, which commands will verify the operational status of router interfaces? (Choose two.)
A. Router# show interfaces
B. Router# show ip protocols
C. Router# debug interface
D. Router# show ip interface brief
E. Router# show start
Answer: A,D
Explanation:
Only two commands “show interfaces” and “show ip interface brief” reveal the status of router interfaces (up/up, for example).
Q9. - (Topic 3)
Refer to the exhibit.
The internetwork is using subnets of the address 192.168.1.0 with a subnet mask of
255.255.255.224. The routing protocol in use is RIP version 1. Which address could be assigned to the FastEthernet interface on RouterA?
A. 192.168.1.31
B. 192.168.1.64
C. 192.168.1.127
D. 192.168.1.190
E. 192.168.1.192
Answer: D
Explanation:
Subnet mask 255.255.255.224 with CIDR of /27 which results in 32 hosts per.
192.168.1.31 is the broadcast address for sunbet '0'
192.168.1.64 is the network address for subnet '2'
192.168.1.127 is the broadcast address for subnet '3'
192.168.1.192 is the network address for subnet '6'
Q10. - (Topic 5)
What are two recommended ways of protecting network device configuration files from outside network security threats? (Choose two.)
A. Allow unrestricted access to the console or VTY ports.
B. Use a firewall to restrict access from the outside to the network devices.
C. Always use Telnet to access the device command line because its data is automatically encrypted.
D. Use SSH or another encrypted and authenticated transport to access device configurations.
E. Prevent the loss of passwords by disabling password encryption.
Answer: B,D
Explanation:
Using a firewall is a must for networks of any size to protect the internal network from outside threats and unauthorized access. SSH traffic is encrypted while telnet is not, so it is always recommended to use SSH.