We provide real cisco 100 105 exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco 100 105 icnd1 Exam quickly & easily. The cisco 100 105 PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco 100 105 icnd1 dumps pdf and vce product and material, you can easily pass the ccent 100 105 pdf exam.


2026 New 100-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/100-105/

P.S. Printable 100-105 braindumps are available on Google Drive, GET MORE: https://drive.google.com/open?id=1p6goOol79JPy5WQ9QjPXU5ZCXFzabnVd


New Cisco 100-105 Exam Dumps Collection (Question 4 - Question 13)

Question No: 4

Which statement about the default switch configuration for remote access managements is true?

A. The system name is set to Cisco.

B. The Telnet password is set to cisco.

C. No default gateway is defined.

D. One IP address is preconfigured.

Answer: C


Question No: 5

Which component of a routing table entry represents the subnet mask?

A. routing protocol code

B. prefix

C. metric

D. network mask

Answer: D

Explanation:

IP Routing Table Entry TypesAn entry in the IP routing table contains the following information in the order presented:

Network ID. The network ID or destination corresponding to the route. The network ID can be class-based, subnet, or supernet network ID, or an IP address for a host route. Network Mask. The mask that is used to match a destination IP address to the network ID. Next Hop. The IP address of the next hop.

Interface. An indication of which network interface is used to forward the IP packet. Metric. A number used to indicate the cost of the route so the best route among possible multiple routes to the same destination can be selected. A common use of the metric is to indicate the number of hops (routers crossed) to the network ID.

Routing table entries can be used to store the following types of routes:

Directly Attached Network IDs. Routes for network IDs that are directly attached. For

directly attached networks, the Next Hop field can be blank or contain the IP address of the interface on that network.

Remote Network IDs. Routes for network IDs that are not directly attached but are available across other routers. For remote networks, the Next Hop field is the IP address of a local router in between the forwarding node and the remote network.

Host Routes. A route to a specific IP address. Host routes allow routing to occur on a per- IP address basis. For host routes, the network ID is the IP address of the specified host and the network mask is 255.255.255.255.

Default Route. The default route is designed to be used when a more specific network ID or host route is not found. The default route network ID is 0.0.0.0 with the network mask of 0.0.0.0.


Question No: 6

Which dynamic routing protocol uses only the hop count to determine the best path to a destination?

A. IGRP

B. RIP

C. EIGRP

D. OSPF

Answer: C


Question No: 7

Scenario:

You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.

Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.

NAT is enabled on router R1.

The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.

R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.

You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.

Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office. Which statement correctly identifies the problem on Router R1?

A. Interesting traffic for NAT ACL is incorrectly configured.

B. NAT configurations on the interfaces are incorrectly configured

C. NAT translation statement incorrectly configured.

D. Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.

Answer: B


Question No: 8

Which command displays the number of times that an individual router translated an inside address to an outside address?

A. show ip protocol 0

B. show ip nat translation

C. show counters

D. show ip route

E. show ip nat statistics

Answer: E


Question No: 9

Which statement is correct about the internetwork shown in the diagram?

A. Switch 2 is the root bridge.

B. Spanning Tree is not running.

C. Host D and Server 1 are in the same network.

D. No collisions can occur in traffic between Host B and Host C.

E. If Fa0/0 is down on Router 1, Host A cannot access Server 1.

F. If Fa0/1 is down on Switch 3, Host C cannot access Server 2.

Answer: E


Question No: 10

Which port-security feature allows a switch to learn MAC addresses dynamically and add them to the running configuration?

A. security violation restrict mode

B. switch port protection

C. sticky learning

D. security violation protect mode

Answer: C

Explanation:

You can configure an interface to convert the dynamic MAC addresses tosticky secure MAC addresses and to add them to the running configuration by enabling sticky learning. To enable sticky learning, enter the switchport port-security mac-address sticky interface configuration command. When you enter this command, the interface converts all the dynamic secure MAC addresses, including those that were dynamically learned before sticky learning was enabled, to sticky secure MAC addresses.


Question No: 11

WAN data link encapsulation types include which of the following? (Choose two.)

A. T1

B. Frame Relay

C. DSL

D. PPP

E. ISDN

Answer: B,D


Question No: 12

When you use the ping command to send ICMP messages across a network, what's the most common request/reply pair you'll see? (Select one answer choice)

A. Echo request and Echo reply

B. ICMP hold and ICMP send

C. ICMP request and ICMP reply

D. Echo off and Echo on

Answer: A


Question No: 13

Which statement is a Cisco best practice for switch port security?

A. Vacant switch ports must be shut down.

B. Empty ports must be enabled in VLAN 1.

C. VLAN 1 must be configured as the native VLAN.

D. Err-disabled ports must be configured to automatically re-enable.

Answer: A


Recommend!! Get the Printable 100-105 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/100-105/ (New 347 Q&As Version)