Testking 200 355 wifund Questions are updated and all ccna wireless 200 355 pdf download answers are verified by experts. Once you have completely prepared with our ccna wireless 200 355 pdf exam prep kits you will be ready for the real 200 355 vce exam without a problem. We have Replace Cisco 200 355 pdf dumps study guide. PASSED ccna wireless 200 355 pdf download First attempt! Here What I Did.


2026 New 200-355 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-355/

Q1. Refer to the exhibit. WLC1 becomes unresponsive due to a power failure at a customer site. How does the access point that is shown in the WLC controller GUI behave now that WLC1 is disabled? 

A. associates to controller 10.201.204.6 

B. associates to controller 10.201.204.11 

C. associates to controller 10.201.204.8 

D. associates to controller 10.201.204.19 

Answer: B 

Q2. Which command path correctly describes how to access and troubleshoot clients with Cisco WCS version 7.0? 

A. Tools > Clients > select displayed client's MAC address 

B. Tools > Clients > enter client's MAC address 

C. Monitor > Clients > click displayed client's MAC address 

D. Monitor > Clients > enter client's MAC address 

Answer: C 

Q3. If an antenna has a dBd of 8.6, what is the dBi value? 

A. 6.2 

B. 6.46 

C. 8.6 

D. 10.74 

E. 12.88 

Answer: D 

Q4. When using a Cisco WLC version 7.0 with a default configuration, how is a remote management HTTPS access connection secured? 

A. The Cisco WLC uses a pre-shared key to authenticate the user, which limits the number of potential users that can access the controller. 

B. The Cisco WLC generates its own local web administration SSL certificate and automatically applies it to the GUI. 

C. The Cisco WLC uses a CA certificate for SSL access. 

D. The Cisco WLC uses HTTPS to secure the HTTP session via a preconfigured password that generates a certificate for each session. 

Answer: B 

Q5. During Layer 2 intercontroller roaming, which two items change? (Choose two.) 

A. SSID 

B. VLAN 

C. IP address 

D. AP 

E. controller 

Answer: D,E 

Q6. A help desk engineer is attempting to perform a remote packet capture on the wireless network. Which access point mode is necessary to perform this function? 

A. sniffer 

B. SE-Connect 

C. monitor 

D. rogue detector 

E. FlexConnect 

Answer: A 

Q7. Which two statements best describe the LAG configuration between a Cisco WLC and a Cisco Catalyst switch? (Choose two.) 

A. The Catalyst switch should be configured for PAgP. 

B. The Catalyst switch should be configured only for Layer 2 load balancing. 

C. The Catalyst switch should be configured for "on" mode. 

D. The Cisco WLC relies on the connected switch to perform the load-balance of traffic. 

E. The Cisco WLC aggregates multiple management interfaces into a single virtual interface. 

Answer: C,D 

Q8. Which operating mode is valid for controllers in a converged access architecture? 

A. switch peer groups 

B. mobility controller 

C. auto-anchor 

D. foreign anchor 

Answer: B 

Q9. Refer to the exhibit. 

Cisco WCS version 7.0 has a configuration mismatch with what is actually running in the controller. Which menu leads to the Audit Status Report? 

A. Security 

B. Monitor 

C. Configure 

D. Services 

E. Administration 

F. Tools 

Answer: C 

Q10. An AP was reset while working on the correct association to a Cisco WCS version 7.0. 

Which item was cleared during the reset? 

A. static IP address 

B. the location ID of the AP 

C. WLC primary, secondary, tertiary 

D. AP name 

E. certificate 

F. Nothing was cleared. 

Answer: F