Testking offers free demo for ccna 200 105 exam. "Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)", also known as 200 105 icnd2 exam, is a Cisco Certification. This set of posts, Passing the Cisco cisco 200 105 exam, will help you answer those questions. The 105 200 Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco ccna 200 105 exams and revised by experts!
2026 New 200-105 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-105/
Q1. - (Topic 1)
What is one benefit of PVST+?
A. PVST+ supports Layer 3 load balancing without loops.
B. PVST+ reduces the CPU cycles for all the switches in the network.
C. PVST+ allows the root switch location to be optimized per VLAN.
D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage.
Answer: C
Explanation:
Per VLAN Spanning Tree (PVST) Introduction http://www.cisco.com/en/US/tech/tk389/tk621/tk846/tsd_technology_support_sub-protocol_home.html Per VLAN Spanning Tree (PVST) maintains a spanning tree instance for each VLAN configured in the network. This means a switch can be the root bridge of a VLAN while another switch can be the root bridge of other VLANs in a common topology. For example, Switch 1 can be the root bridge for Voice data while Switch 2 can be the root bridge for Video data. If designed correctly, it can optimize the network traffic. http://www.ciscopress.com/articles/article.asp?p=102157&seqNum=4
Topic 2, Routing Technologies
Q2. - (Topic 2)
Refer to the exhibit.
If the router R1 returns the given output and has not had its router ID set manually, what address will EIGRP use as its router ID?
A. 192.168.1.2
B. 172.16.4.1
C. 192.168.10.2
D. 1.1.1.1
Answer: D
Explanation:
The router ID is selected according to the following rules: manual configuration highest up/up loopback highest up/up physical interface
Q3. - (Topic 2)
Refer to the exhibit.
C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
A. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Explanation:
http://www.cisco.com/en/US/tech/tk389/tk815/technologies_configuration_example09186a 00800949fd.shtml https://learningnetwork.cisco.com/servlet/JiveServlet/download/5669-2461/Router%20on%20a%20Stick.pdf.
Q4. - (Topic 2)
A router is running three routing processes: RIP, OSPF, and EIGRP, each configured with default characteristics. Each process learns a route to the same remote network.
If there are no static routes to the destination and none of the routes were redistributed, which route will be placed in the IP routing table?
A. the route learned through EIGRP
B. the route learned through OSPF
C. the route learned through RIP
D. the route with the lowest metric
E. all three routes with the router load balancing
Answer: A
Reference:
http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml
Administrative distance is the feature that routers use in order to select the best path.
Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value. Lowest Administrative distance will be chosen first.
Q5. - (Topic 3)
Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two.)
A. CHAP uses a two-way handshake.
B. CHAP uses a three-way handshake.
C. CHAP authentication periodically occurs after link establishment.
D. CHAP authentication passwords are sent in plaintext.
E. CHAP authentication is performed only upon link establishment.
F. CHAP has no protection from playback attacks.
Answer: B,C
Explanation:
Understanding and Configuring PPP CHAP Authentication http://www.cisco.com/en/US/tech/tk713/tk507/technologies_tech_note09186a00800b4131. shtml
One-Way and Two-Way Authentication CHAP is defined as a one-way authentication method. However, you use CHAP in both directions to create a two-way authentication. Hence, with two-way CHAP, a separate three-way handshake is initiated by each side. In the Cisco CHAP implementation, by default, the called party must authenticate the calling party (unless authentication is completely turned off). Therefore, a one-way authentication initiated by the called party is the minimum possible authentication. However, the calling party can also verify the identity of the called party, and this results in a two-way authentication. One-way authentication is often required when you connect to non-Cisco devices.
Q6. - (Topic 1)
At which layer of the OSI model is RSTP used to prevent loops?
A. physical
B. data link
C. network
D. transport
Answer: B
Explanation: RSTP and STP operate on switches and are based on the exchange of Bridge Protocol Data Units (BPDUs) between switches. One of the most important fields in BPDUs is the Bridge Priority in which the MAC address is used to elect the Root Bridge , RSTP operates at Layer 2. http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cf a.shtml
Q7. - (Topic 3)
Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms?
A. HDLC
B. PPP
C. X.25
D. Frame Relay
Answer: B
Explanation:
High-Level Data Link Control (HDLC) - HDLC is the default encapsulation type on point-to-point, dedicated links, and circuit-switched connections. It is used typically when communicating between two Cisco devices. It is a bit-oriented synchronous data link layer protocol. Point-to-Point Protocol (PPP) - Provides router-to-router and host-to network connections over synchronous and asynchronous circuits. PPP was designed to work with several network layer protocols, such as IP, and IPX. PPP also has built in security mechanisms such as PAP and CHAP X.25/Link Access Procedure, Balanced (LAPB) - ITU-T standard that defines how connections between DTE and DCE are maintained for remote terminal access and computer communications in public data networks. X.25 specifies LAPB, a data line layer protocol. X.25 is a predecessor to Frame Relay. Frame Relay - Industry standard, switched data link layer protocol that handles multiple virtual circuits. It is a next-generation to X.25 that is streamlined to eliminate some of the time-consuming processes (such as error correction and flow control) that were employed in X.25.
Q8. - (Topic 1)
Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)
A. 802.1Q native VLAN frames are untagged by default.
B. 802.1Q trunking ports can also be secure ports.
C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D. 802.1Q trunks require full-duplex, point-to-point connectivity.
E. 802.1Q trunks should have native VLANs that are the same at both ends.
Answer: A,C,E
Explanation:
CCNA Self-Study (ICND Exam): Extending Switched Networks with Virtual LANs http://www.ciscopress.com/articles/article.asp?p=102157&seqNum=2
Q9. - (Topic 2)
Refer to the exhibit.
What address is a feasible successor?
A. 172.16.4.0
B. 10.1.4.4
C. 10.1.2.2
D. 172.16.3.0
Answer: C Explanation:
The feasible condition states:
“To qualify as a feasible successor, a router must have an AD less than the FD of the current successor route”.
In this case, we see 10.1.2.2 shows an AD less than the current successor of 10.1.4.4
Q10. - (Topic 1)
Which protocol provides a method of sharing VLAN configuration information between two Cisco switches?
A. STP
B. VTP
C. 802.1Q
D. RSTP
Answer: B
Explanation:
Understanding VLAN Trunk Protocol (VTP) http://www.cisco.com/en/US/tech/tk389/tk689/technologies_tech_note09186a0080094c52. shtml
Introduction VLAN Trunk Protocol (VTP) reduces administration in a switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain. This reduces the need to configure the same VLAN everywhere. VTP is a Cisco-proprietary protocol that is available on most of the Cisco Catalyst series products.