we provide Actual Cisco cisco 200 125 test question which are the best for clearing 200 125 cisco test, and to get certified by Cisco CCNA Cisco Certified Network Associate CCNA (v3.0). The 200 125 ccna v3 0 Questions & Answers covers all the knowledge points of the real 200 125 ccna v3 0 exam. Crack your Cisco ccna 200 125 pdf Exam with latest dumps, guaranteed!
2026 New 200-125 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-125/
P.S. Actual 200-125 samples are available on Google Drive, GET MORE: https://drive.google.com/open?id=1qSmqe9lmg23sR5XECqlhobCqcIIdpdHn
New Cisco 200-125 Exam Dumps Collection (Question 5 - Question 14)
Q5. Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00:/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and it is ::1.
E. If a global address is assigned to an interface, then that is the only allowable address for the interface.
Answer: A,D
Explanation:
Below is the list of common kinds of IPv6 addresses:
Q6. An administrator is trying to ping and telnet from SwitchC to RouterC with the results shown below.
Click the console connected to RouterC and issue the appropriate commands to answer the questions.
Which will fix the issue and allow ONLY ping to work while keeping telnet disabled?
A. Correctly assign an IP address to interface fa0/1.
B. Change the ip access-group command on fa0/0 from u201cinu201d to u201coutu201d.
C. Removeaccess-group 106 infrom interface fa0/0 and addaccess-group 115 in.
D. Removeaccess-group 102 outfrom interface s0/0/0 and addaccess-group 114 in
E. Removeaccess-group 106 infrom interface fa0/0 and addaccess-group 104 in.
Answer: E
Explanation:
Letu2021s have a look at the access list 104:
The question does not ask about ftp traffic so we donu2021t care about the two first lines. The 3rd line denies all telnet traffic and the 4th line allows icmp traffic to be sent (ping). Remember that the access list 104 is applied on the inbound direction so the 5th line u201caccess-list 104 deny icmp any any echo-replyu201d will not affect our icmp traffic because the u201cecho-replyu201d message will be sent over the outbound direction.
Q7. Refer to the exhibit.
The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three.)
A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.
Answer: B,D,F
Explanation:
The ports on the switch are not up indicating it is a layer 1 (physical) problem so we should check cable type, power and how they are plugged in.
Q8. Refer to the exhibit.
A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.)
A. host A IP address: 192.168.1.79
B. host A IP address: 192.168.1.64
C. host A default gateway: 192.168.1.78
D. host B IP address: 192.168.1.128
E. host B default gateway: 192.168.1.129
F. host B IP address: 192.168.1.190
Answer: A,C,F
Explanation:
Itu2021s a u201crouter-on-a-sticku201d configuration. Which means each host in the VLAN must corresponds with the VLAN configured on the sub-interfaces.
VLAN 10 is configured on fa0/0.10 and VLAN 20 on fa0/0.20. So each hosts in VLAN 10 must use fa0/0.10 IP address as their default gateway, each hosts must also be in the same subnet as fa0/0.10 IP u2013 same with hosts in VLAN 20.
So find out the usable IP addresses on each sub-interfaces u2013 for 192.168.1.78 /27: 192.168.1.65 u2013 .94 and for 192.168.1.130 /26: 192.168.1.128 u2013 .190.
Host A (using port 6 u2013 VLAN 10) must use IP 192.168.1.79, default gateway 192.168.1.78. Host B (using port 9 u2013 VLAN 20) must use IP 192.168.1.190, default gateway 192.168.1.130.
Q9. Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Answer: B,C
Explanation:
u2711 A single interface may be assigned multiple addresses of any type (unicast, anycast, multicast).
u2711 Every IPv6-enabled interface must contain at least one loopback and one link-local
address.
u2711 Optionally, every interface can have multiple unique local and global addresses.
Reference: IPv6 Addressing at a Glance u2013 Cisco PDF
Q10. Scenario
Refer to the topology. Your company has connected the routers R1, R2, and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
Which path does traffic take from R1 to R5?
A. The traffic goes through R2.
B. The traffic goes through R3.
C. The traffic is equally load-balanced over R2 and R3.
D. The traffic is unequally load-balanced over R2 and R3.
Answer: A
Explanation:
Using the u201cshow ip int brief commandu201d on R5 we can see the IP addresses assigned to this router. Then, using the u201cshow ip routeu201d command on R1 we can see that to reach 10.5.5.5 and 10.5.5.55 the preferred path is via Serial 1/3, which we see from the diagram is the link to R2.
Q11. Refer to the exhibit.
Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)
A. The cable that is connected to S0/0 on RouterA is faulty.
B. Interface S0/0 on RouterB is administratively down.
C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.
Answer: E,F
Explanation:
From the output we can see that there is a problem with the Serial 0/0 interface. It is enabled, but the line protocol is down. There could be a result of mismatched encapsulation or the interface not receiving a clock signal from the CSU/DSU.
Q12. Refer to the exhibit.
What is the cause of the Syslog output messages?
A. The EIGRP neighbor on Fa0/1 went down due to a failed link.
B. The EIGRP neighbor connected to Fa0/1 is participating in a different EIGRP process, causing the adjacency to go down.
C. A shut command was executed on interface Fa0/1, causing the EIGRP adjacency to go
down.
D. Interface Fa0/1 has become error disabled, causing the EIGRP adjacency to go down.
Answer: C
Explanation:
The first lines of the message show that a configuration change was made, and that the fa0/1 interface changed to a state of administratively down. This can only be done by issuing the shutdown command. The last line indicates that this caused an EIGRP neighbor adjacency to go down.
Q13. A network administrator is configuring ACLs on a Cisco router, to allow traffic from hosts on networks 192.168.146.0, 192.168.147.0, 192.168.148.0, and 192.168.149.0 only. Which two ACL statements, when combined, would you use to accomplish this task? (Choose two.)
A. access-list 10 permit ip 192.168.146.0 0.0.1.255
B. access-list 10 permit ip 192.168.147.0 0.0.255.255
C. access-list 10 permit ip 192.168.148.0 0.0.1.255
D. access-list 10 permit ip 192.168.149.0 0.0.255.255
E. access-list 10 permit ip 192.168.146.0 0.0.0.255
F. access-list 10 permit ip 192.168.146.0 255.255.255.0
Answer: A,C
Explanation:
u201caccess-list 10 permit ip 192.168.146.0 0.0.1.255u201d would allow only the 192.168.146.0 and
192.168.147.0 networks, and u201caccess-list 10 permit ip 192.168.148.0 0.0.1.255u201d would allow only the 192.168.148.0 and 192.168.149.0 networks.
Q14. Refer to exhibit.
A network administrator cannot establish a Telnet session with the indicated router. What is the cause of this failure?
A. A Level 5 password is not set.
B. An ACL is blocking Telnet access.
C. The vty password is missing.
D. The console password is missing.
Answer: C
Explanation:
The login keyword has been set, but not password. This will result in the u201cpassword
required, but none setu201d message to users trying to telnet to this router.
Recommend!! Get the Actual 200-125 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/200-125/ (New 889 Q&As Version)