Examcollection offers free demo for 200-150 exam. "DCICN Introducing Cisco Data Center Networking", also known as 200-150 exam, is a Cisco Certification. This set of posts, Passing the Cisco 200-150 exam, will help you answer those questions. The 200-150 Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco 200-150 exams and revised by experts!


2026 New 200-150 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-150/

Q1. Refer to the exhibit. 

What two conclusions can be mode based upon the output? (Choose two.)

A. regular fromat WWNs are being used

B. the command show flogl database was run

C. the command show fcns database vsan 1 was run

D. registered name formate WWNs are being used

E. extended format WWNs are being used.

Answer: B,E

Q2. An engineer is configuring a new MDS switch. The switch is powered on, the customer connects to the console, and the initial setup script is started.

Which two items can be configured during this setup process?

A. default port-channel mode

B. default port VSAN membership

C. default switch port interface state

D. default zone mode

E. default storage VDC

Answer: C,D

Q3. What two actions can be taken to enable inter-VLAN communications in the data center? (Choose two.)

A. extend Layer 2 services to a Layer 3 capable VLAN using Layer 3 tunneling.

B. use a routing protocol to direct packets into the Layer 2 network

C. connect Layer 2 VLANs together with 802.1Q trunks

D. deploy a router as a Layer 3 services gateway attached inside each Layer 2 VLAN

E. install a Layer 3 capable switch in the data center.

Answer: D,E

Q4. Which two options are benefits of deploying FCoE beyond the access layer?

A. higher throughput compared to native Fibre Channel switches.

B. FCoE cannot be deployed beyond the access layer.

C. reduction in equipment requirements.

D. improved security compared to traditional Fibre Channel.

E. increased application support.

Answer: A,C

Q5. What are two features of a bridge? (Choose two.)

A. Reliable transmission

B. Operate at OSI Layer 2

C. Operate at OSI Layer 3

D. Create multiple broadcast domains

E. Create multiple collision domains

F. Flood input packets to all ports

G. Drop IP packets with invalid destination ports

Answer: B,E

Explanation:

"- a bridge is a two interfaces device that creates 2 collision domains, since it forwards the traffic it receives from one interface only to the interface where the destination layer 2 device (based on his mac address) is connected to. A bridge is considered as an "intelligent hub" since it reads the destination mac address in order to forward the traffic only to the interface where it is connected"

https://learningnetwork.cisco.com/thread/1734

Q6. Which device would you select to partition a network into VLANs?

A. repeater

B. bridge

C. switch

D. router

E. hub

Answer: C

Q7. Which command can change the sequence of a router boot process?

A. config-register

B. configuration-register

C. conf-register

D. config-registration

Answer: A

Q8. Which option describes what a switch does after it items that a host has connected to a switch port?

A. Flood the frame only on all of its trunk ports.

B. Create a MAC to port mapping entry in MAC table.

C. Flood the frame only on all of its access ports.

D. Discard the frame.

Answer: B

Q9. Which statement Is true regarding configuring NPV mode?

A. When you enable NPV, the system configuration is erased and t* switch reboots

B. When you enable NPV. the system configuration is not erased and the does not switch reboot

C. In Exhibit 3 NPV is enabled. but Server interface to the external switch is not bed to correct vfc 2/1.

D. m NPV mode, the core switch relays traffic from server-side ports to the edge switch and core swtich provides N ports.

Answer: A

Explanation: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guid e/cli_rel_4_0_1a/CLIConfigurationGuide/npv.html

Q10. Which command can change the sequence of a router boot process?

A. config-register

B. configuration-register

C. conf-register

D. config-registration

Answer: A