It is impossible to pass Cisco 200-601 exam without any help in the short term. Come to Ucertify soon and find the most advanced, correct and guaranteed Cisco 200-601 practice questions. You will get a surprising result by our Far out Managing Industrial Networking for Manufacturing with Cisco Technologies practice guides.


2026 New 200-601 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-601/

Q1. A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104. Both standard controllers must monitor a photocell on this machine. Which IP address is used to transfer this status information? 

A. 10.17.104.16 

B. 192.168.1.16 

C. 239.192.3.16 

D. 239.192.254.16 

Answer: C 

Q2. Refer to the exhibit. Which lines represent a CIP connection being established between two devices? 

A. 2914 and 2915 

B. 2918 and 2921 

C. 2920 and 2924 

D. 2937 and 2940 

Answer: B 

Q3. If.the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays? 

A. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 4 Switch(config-alarm-prof)#relay minor 1 

B. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 3 Switch(config-alarm-prof)#relay minor 1 

C. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 3 

D. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 4 

Answer: A 

Q4. Which best describes.the difference between 802.11n and 802.11ac? 

A. 802.11ac offers more channels over more bands than 802.11n 

B. 802.11ac MCS 1 is about twice as fast as 802.11n MCS1 

C. 802.11ac offers more modulation schemes than 802.11n 

D. 802.11ac 1SS MCS 9 is allowed over a 20, 40, 80 and 160 MHz channel, while 802.11n 1SS MCS 9 is only allowed over a 20 or 40 MHz channel. 

Answer: C 

Q5. Refer to the exhibit. 

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in: 

L2SW4# show mls interface GigabitEthernet 1/1 statistics 

<output omitted> 

output queues dropped: 

queue:. threshold1. threshold2. threshold3  

queue 0. 0. 0. 0  

queue 1. 309232345. 450. 0. 

queue 2. 300. 10. 0. 

queue 3. 91. 0. 0  

Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two) 

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue 

B. Increase the buffer allocation for input queue 1 

C. Increase the buffer allocation for output queue 1 

D. Alter the service policy to police to a higher CIR 

E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue 

Answer: C,E 

Q6. What is the reason that ProfiNET frames are discarded by default on Catalyst switches? 

A. ProfiNET uses a nonstandard Ethernet frame format 

B. The frames have an 802.1q tag with VLAN ID equal to 0 (zero) 

C. Catalyst switches do not support ProfiNET traffic 

D. A ProfiNET VLAN must be configured and enabled on a Catalyst switch 

Answer: B 

Q7. Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50? 

A. ptp mode boundary ptp priority1 10 ptp priority2 50 

B. ptp mode boundary ptp priority1 50 ptp priority2 10 

C. ptp mode e2etransparent ptp priority1 50 ptp priority2 10 

D. ptp mode e2etransparent ptp priority1 10 ptp priority2 50 

Answer: A 

Q8. Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion? 

A. CIP Motion requires a star topology which is not supported by REP. DLR is a suitable resiliency protocol for CIP motion. 

B. REP convergence is not fast enough. DLR is a suitable resiliency protocol for CIP motion. 

C. CIP Motion requires a star topology which is not supported by REP. RPVST+.is a suitable resiliency protocol for CIP motion. 

D. REP convergence is not fast enough. RPVST+.is a suitable resiliency protocol for CIP motion. 

Answer: B 

Q9. Refer to the exhibit. 

What issue does this topology present for the represented traffic flow? 

A. Standard Produce/Consume traffic is not suitable for an 802.11 wireless environment. 

B. Only one of the Work Group Bridges can transmit at a time, because 802.11 is half duplex. 

C. The Converged Plant-wide Ethernet best practices for 802.11 wireless don't allow for PAC to PAC traffic. 

D. I/O control traffic should utilize the 2.4 GHz band based on best practices. 

Answer: B 

Q10. Which statement is correct regarding Media Redundancy Protocol (MRP) in a ring of ProfiNET devices? 

A. When a link fault is detected, MRP rings must converge in less than 100 milliseconds 

B. MRP defines two device roles, Media Redundancy Master and Media Redundancy Client 

C. MRP can support rings of up to 250 devices 

D. MRP is only supported on network switches 

Answer: B