It is impossible to pass Cisco 200-601 exam without any help in the short term. Come to Actualtests soon and find the most advanced, correct and guaranteed Cisco 200-601 practice questions. You will get a surprising result by our Up to the minute Managing Industrial Networking for Manufacturing with Cisco Technologies practice guides.


2026 New 200-601 Exam Dumps with PDF and VCE Free: https://www.2passeasy.com/dumps/200-601/

Q1. You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on-line with RSLogix5000. When do the changes you have made get published to the switch? 

A. While online in RSLogix 5000 software the changes made in the AOP are pushed to the switch after pressing the Set button. 

B. All of the changes are automatically pushed to the switch. 

C. Changes to the AOP can only be made from the switch, not in RSLogix 5000. 

D. RSLogix 5000 will push the changes in the AOP to the Stratix 5700 when you right click on the switch, and choose download to switch 

Answer: A 

Q2. Refer to the exhibit. The Robot Cell is in a bottling plant. This cell environment needs to consider high flex, EMI, and possible exposure to moisture. Which physical media components need to be considered to prevent network degradation or interruptions? 

A. Stranded, shielded wire with an industrial jacket and M12 connectors 

B. Solid, unshielded commercial jacket wire, and M12 connectors 

C. Stranded, unshielded wire with an industrial jacket, and commercial grade RJ45 connectors 

D. Solid, shielded wire with commercial grade jacket, and commercial grade RJ45 connectors 

Answer: A 

Q3. How are I/O timeout and Safety I/O timeout calculated? 

A. An I/O connection will timeout based on the lower of 4x RPI or 100ms. Safety I/O timeout is calculated as 4xRPI. 

B. An I/O connection will timeout based on the lower of 3x RPI or 100ms. Safety I/O timeout is calculated as 3xRPI. 

C. An I/O connection will timeout based on the lower of 4x RPI or 150ms. Safety I/O timeout is calculated as 2xRPI. 

D. An I/O connection will timeout based on the lower of 3x RPI or 150ms. Safety I/O timeout is calculated as 3xRPI. 

Answer: A 

Q4. Which five are characteristics that describe Cisco Industrial switches? (Choose five) 

A. Din rail mount 

B. 19 inch rack mount 

C. Fanless 

D. Fans 

E. Swappable SD flash card 

F. Alarm relay 

G. -5oC to 45oC operating environment 

H. ProfiNET conformance class C compliance 

Answer: A,B,C,E,F 

Q5. Which statement is correct regarding ProfiNET communication classes? 

A. ProfiNET-RT traffic is carried in UDP and TCP packets B. ProfiNET-NRT is used to carry time critical status information 

C. ProfiNET-IRT requires switches with hardware time scheduling capabilities 

D. ProfiNET-NRT is prioritized as Layer-2 Class-of-Service 1 (CoS 1) 

Answer: C 

Q6. Refer to the exhibit. 

NAT has been configured on the router 'GW' and the IP addresses of router 'GW' have been configured properly. Users of PC1 and PC2 are able to ping the IP address 

198.51.100.1 but are unable to reach any other IP addresses on the Internet. The ISP confirmed that their configuration is correct. Which option would likely correct the problem? 

A. ip access-list extended ACL_OUTBOUND permit ip 10.1.1.0 0.0.0.255 any 

interface Ethernet1 ip access-group ACL_OUTBOUND out 

B. interface Ethernet1 ip nat outside 

C. interface Ethernet0 ip nat inside 

D. ip route 0.0.0.0 0.0.0.0 198.51.100.1 

Answer: D 

Q7. Refer to the exhibit. 

Which values are correct for AP 2 to allow for efficient roaming? 

A. Channel 6, SSID Sittingduck, BSSID 00:0a:0b:0c:0d:0e 

B. Channel 1, SSID Sittingduck, BSSID 00:01:02:03:04:05 

C. Channel 1, SSID Sittingduck, BSSID 00:0a:0b:0c:0d:0e 

D. Channel 6, SSID Sittingduck, BSSID 00:01:02:03:04:05 

Answer: A 

Q8. What is the reason that ProfiNET frames are discarded by default on Catalyst switches? 

A. ProfiNET uses a nonstandard Ethernet frame format 

B. The frames have an 802.1q tag with VLAN ID equal to 0 (zero) 

C. Catalyst switches do not support ProfiNET traffic 

D. A ProfiNET VLAN must be configured and enabled on a Catalyst switch 

Answer: B 

Q9. What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data? 

A. RPI at 50% of IO rate 

B. RPI at 25% of IO rate 

C. PI to 25% of PAC scan rate 

D. Set RPI to 50% of PAC scan rate 

Answer: A 

Q10. You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on? 

A. Lattency and Jitter 

B. Redundancy and high availability 

C. Explicit and Implicit messaging 

D. This cycle time is not possible on an Ethernet network 

E. Gigabit port speed 

Answer: A