The Updated Guide To 200-601 exam dumps

Q1. Refer to the exhibit. 

Which three options are needed to configure NAT on router GW so PC1 and PC2 will be able to ping 203.0.113.1? (Choose three) 

A. interface Ethernet0 ip nat inside interface Ethernet1 ip nat outside 

B. ip access-list standard ACL_NAT permit 10.1.1.0 0.0.0.255 

C. ip nat inside source static tcp 10.1.1.0 80 interface Ethernet1 80 

D. interface Ethernet0 ip nat outside interface Ethernet1 ip nat inside 

E. ip nat inside source list ACL_NAT interface Ethernet1 overload 

F. ip access-list extended ACL_NAT permit tcp 10.1.1.0 0.0.0.255 any eq 80 

View Answer

Q2. Which scenario represents the correct configuration to support the SSIDs of this autonomous access point? 

A. 

B. 

C. 

D. 

View Answer

Q3. A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two) 

A. DLR is designed for single network operation at the machine level 

B. Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure 

C. DLR is the only resiliency technology that is supported by CIP Safety 

D. Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control 

E. Half of the network traffic goes clockwise on the ring and the other half counter-clockwise, reducing by 50% the impact of cable failure 

View Answer

Q4. It is determined that an intermittent high packet loss event is occurring within a segment of the network. The assigned task is to determine the cause. Which of these conditions should be suspected? 

A. 

B. 

C. 

D. 

View Answer

Q5. Refer to the exhibit. 

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in: 

L2SW4# show mls interface GigabitEthernet 1/1 statistics 

<output omitted> 

output queues dropped: 

queue:. threshold1. threshold2. threshold3  

queue 0. 0. 0. 0  

queue 1. 309232345. 450. 0. 

queue 2. 300. 10. 0. 

queue 3. 91. 0. 0  

Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two) 

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue 

B. Increase the buffer allocation for input queue 1 

C. Increase the buffer allocation for output queue 1 

D. Alter the service policy to police to a higher CIR 

E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue 

View Answer

Q6. You have reached the limit of IPv4 IGMP groups available on a Cisco IE 3000 switch that was deployed using the Express Setup. Which CLI command will increase the number of 

available IPv4 IGMP groups and multicast routes from 256 to 1000 on this switch? 

A. switch(config)#sdm prefer routing 

B. switch(config)#sdm prefer vlan igmp 

C. switch(config)#sdm prefer routing igmp 

D. switch(config)#sdm prefer vlan 

View Answer

Q7. ProfiNET has been disabled on a Cisco Industrial Ethernet switch. Which CLI command.will correctly enable ProfiNET on the switch? 

A. switch(config)#profinet 

B. switch(config-if)#switchport profinet vlan 10 

C. switch(config)#vlan 10 profinet 

D. switch#enable profinet 

View Answer

Q8. Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI? 

A. 2919, 2923, 2926 

B. 2920, 2926, 2929 

C. 2922, 2929, 2935 

D. 2914, 2915, 2916 

View Answer

Q9. Which three network mechanisms can be used for securely segmenting an industrial network? (Choose three) 

A. VLANs 

B. OSPF 

C. REP 

D. VRFs 

E. Firewalls 

F. Spanning-tree 

View Answer

Q10. Refer to the exhibit. 

L3SW1 has a spanning-tree priority of 8192 set on VLANs 1, 300, and 301, and these VLANs are configured on and trunked between all switches. Executing the command show spanning-tree blockedports on L2SW5 results in: 

L2SW5# show spanning-tree blockedports 

Name.Blocked Interfaces List VLAN0001.Gi1/1 

VLAN0300.Gi1/1 

VLAN0301.Gi1/1 

An additional VLAN, VLAN302, is defined on all switches and trunked between them. VLAN302 access ports are set up on each of the switches and PLC#1, I/O#1, and the PanelView are attached. You expect the new VLAN to be listed as blocked on interface GigabitEthernet1/1 of L2SW5 but it is not. The three new devices are able to communicate with each other. 

After executing the same command on all switches you see this output on L2SW4: 

L2SW4# show spanning-tree blockedports 

Name.Blocked Interfaces List 

VLAN0001.Gi1/2 

VLAN0300.Gi1/2 

VLAN0301.Gi1/2 

Why is VLAN302 forwarding on L2SW5 interface GigabitEthernet 1/1 and L2SW4 interface GigabitEthernet 1/1 and 1/2? 

A. VLAN302 is not configured in the VLAN database on L2SW5 

B. VLAN302 is not in the allowed list on the L2SW5 interface GigabitEthernet1/1 trunk 

C. L2SW4 is the spanning tree root for VLAN 302 

D. The FO3 fiber-optic cable between L2SW4 and L2SW5.is damaged 

View Answer