how many questions of 210-065 vce?

Q1. When placing a call from Cisco Jabber Video for TelePresence to the Cisco TelePresence System Codec C40, which FECCs are available? 

A. Only zoom-in and zoom-out are available. 

B. Only left and right are available. 

C. Only up and down are available. 

D. No FECC is available. 

E. Left, right, up, down, zoom-in, and zoom-out are all available. 

View Answer

Q2. Refer to the exhibit. 

An employee is reviewing the logs from a Cisco TelePresence System unit due to reports of calls being dropped. Which log entry explains the reason for the call failure? 

A. INFO Packet loss detected: 100% loss - no media stream received in the last 10 seconds 

B. INFO Jitter buffers increased 

C. INFO admin CLI login from 10.160.134.15:51151 

D. INFO Main Video stream packet loss detected on the center codec 

View Answer

Q3. Refer to the exhibit. 

A call with a destination alias of 15551001234 reaches a Cisco TelePresence VCS. Which transform will the destination alias match? 

A. Transform 1 

B. Transform 2 

C. Transform 3 

D. Transform 4 

View Answer

Q4. Refer to the exhibit. 

Which system tab can be used to add video infrastructure devices and endpoints? 

A. Navigator 

B. System Overview 

C. Configuration Templates 

D. Provisioning 

E. Administrative Tools 

View Answer

Q5. Which two protocols can be used with the Cisco TelePresence Content Server to allow users to share content from their laptops? (Choose two.) 

A. BFCP 

B. H.239 

C. PCoIP 

D. Switched Presentation 

E. SCCP 

F. RDP 

View Answer

Q6. Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.) 

A. enhanced continuous presence 

B. active speaker switching 

C. continuous presence 

D. speaker switching 

E. room switching 

F. active continuous presence 

View Answer

Q7. A network engineer wants to automate the monitoring of Cisco TelePresence TX systems. Which step should the engineer take first? 

A. Configure Cisco TMS on the codec. 

B. Configure Medianet on the codec. 

C. Configure NTP on the codec. 

D. Configure Multiway on the codec. 

E. Configure SNMP on the codec. 

View Answer

Q8. In this item, you will need to use all information presented to you to successfully answer the question. 

The Cisco Telepresence Codec C90 is unable to call the Cisco IP Video Phone. Assuming that the calling search space has been configured correctly, which of the these can cause this issue? 

A. The Cisco Telepresence Codec C90 can only be registered to a Cisco Telepresence Video Communication Server. 

B. A multipoint control unit is required in order for the call to work. 

C. The Cisco Telepresence Codec C90 can only be registered as a SIP endpoint to Cisco Unified Communications Manager. H.323 is not supported. 

D. URI dialing has not been configured on Cisco Unified Communications Manager. 

E. The Cisco Telepresence Codec C90 Profile 1 > CallSetupMode must be configured as a gateway since Cisco Unified Communications Manager does not have a gatekeeper functionality. 

F. The Cisco Telepresence Codec C90 is not registered as a SIP endpoint on Cisco Unified Communications Manager. The Cisco Telepresence Codec C90 needs to be registered as both SIP and H.323. 

View Answer

Q9. Cisco Video Surveillance Video Encoder cards perform which function? 

A. the ability to use existing analog equipment with an IP-enabled video surveillance system 

B. the ability to convert low-resolution video to high-definition video for video surveillance 

C. the ability to stream digital media to digital media in an IP-enabled video recording environment 

D. the ability to encrypt raw video signals to secure video signals 

View Answer

Q10. A desktop video endpoint is needed that can support a PrecisionHD camera design and a built-in display, and is Bluetooth-ready and multisite-capable. Which desktop endpoint supports all of these requirements? 

A. SX20 

B. EX60 

C. SX80 

D. EX90 

View Answer